Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11743899
This electronic clock assembly is seven and a half inches long. It is three inches wide and is intended for use with a range's control panel.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
Turn off power to oven. open top oven door and remove the four screws holding the display unit in place. Pull out on the bottom and lift up. Disconnect the wires and lay unit on counter.Remove the four screws holding the clock display and replace with new part. Reassmble. Ahhh lights. Pray that you new unit doesn't burn out in four years. The end.
Help other customers find the most helpful instructions.
Were these instructions helpful?
First, I turned off the circuit breaker to the double over.Second, I opened the oven door. At the top of the frame, underneath the panel are four screws (not evenly spaced) that I removed. I held onto the glass control panel, not wanting it to come down when I removed the screws, but this was unnecessary as there is a ridge in the back to keep it in place.Third, I lifted out the glass control panel. There are two sets of wires going from the oven to the control panel. One set of wire connects in two places (three connections in total).Fourth, I simply disconnected these wires from the chips (lifting them off), trivial. They all have different connectors, so there is no chance of getting them mixed up. If you have never touched any new electronics and are completely unfamiliar with plugging wires on a chip, you may take note of the orientations of the connectors), but it is fairly dummy-proof.Fifth, there are four screws holding the display in place. Used the socket wrench for these (they go through the holes you see on the side of the unit in the picture). Sixth, reversed the last operation, screwing the new display in place on the removed panel.Seventh, Some of the teeth on the connector of my new display were bent over. I bent these straight so the connector would go over them, and reconnected the wires, carefully(!)Eighth, slipped the glass panel in place. When seated properly, it does not shift. Ninth, secured panel with the four initial screws.Tenth, turned on the circuit breaker.Eleventh, was shocked by how bright the new LED was!
I removed two screws to take the control panel off. The electronic display is held in place with four screws which are easily removed with a nut driver.The wiring work is extremely simple.To replace the element, I removed the oven racks, took two screws out, disconnected the two wires, then replaced the element by reversing the process.Both jobs took less than 20 minutes and that includes two trips to the breaker box in the basement.
First, I searched ythe partselect.com web site for "Dim over display for Jenn-Air double over" and found an answer to some one with the exact same model as me. The answer said to order the "clock assembly" and all would be solved.So, I ordered the assembly, it arrived. First thing I did was turn off the circut breaker for the over! I removed 4 screws holding the oven display in place. With those 4 screws removed, I was able to remove the clock assembly with 4 more screws and 3 cable connecters.Put the new assembly in place, hooked up the connectors and turned the circut breaker back on. Everything was done and working within 15 minutes! Could not have been easier, it's great to have the display back again, we can now tell the oven temp, how much time is left on the timer, etc!
Turned off power to range - Removed the 4 screws holding the glass assembly in (front glass touch panel on range). and lifted up to expose wiring and electrical components. Pulled off all electrical plugs (4) and detached clock component from assembly by unscrewing 4 screws. Replaced new assembly, secured with 4 screws, plugged in all 4 plugs - turned circuit breaker on to restore power - WaLah!! That SIMPLE!
Turned breaker off at circuit panel.Opened top oven door. Removed 4 srews to lift up panel. Removed 4 hex head screws which held clock assembly in place. Unplugged 3 wiring connections. Plugged in new part and screwed back into place. Returned panel wih 4 screws. Switched breaker back on and smiled because it worked!!
Soooooooo easy- I am a house wife and did it- turned off power and unscrewed 4 screws and then a couple more and unplugged wires then replugged to new piece/part then screwed all screwss back in- EASY- woulda cost 400 for parts and labor
Turned off power,Removed screws holding panel on,Lifted off panel,Unplugged wiring,Removed 4 nuts holding clock assembly,Replaced assembly with new one and secured with the 4 nuts,Plugged in wiring,Installed panel and screwsTurned on power,Finished in less than 15 minutes.Owner was all smiles and very happy!Great service from PartSelect on ordering and delivery!
Removed 4 screws, lifted panel off, disconnected old board replaced with new.
Switched off power !Removed the control panel by removing four philips screws under the panel. marked all the connectors with a permanent markers (socket & cable) to be able to identify the right direction. Removed the old clock assembly by removing 4 hex screws. Then assembled new unit and reversed steps...Clock and oven temperature is again readable and very bright! initially I got a replacement part that showed the same error as the original part, but this unit was replaced within one (!) day under the Partselect warranty plan. Good job!
The total repair time was less than 5 minutes. I turned off the circut breaker to my oven. Directions were very easy, remove 4 screws, take plugs off old unit, place them on new unit, remove 4 screws with nut driver, place new clock in place and put the screws back in. Go out and turn on power to oven. Set the clock.
Opened breaker feeding power to ovenRemoved 4 screws on underside of front panel; display module is attached to back side of panel.Unplugged wiring harness from panel circuit boards and display module. Set panel face down on towel to keep from scratching it.Removed 2 screws holding display to panelReplace module and re-attached to panelPlugged harnesses back inRe-attached panelTurn on breaker. Done.
Easy sneezyFour hands made it easier1- removed 4 screws 2- had friend hold the whole assembly3- removed the 2 screws holding clock assembly4- removed the electronic connections5- installed the new assembly with 2 scews6- connected the electronic connections7- reattached the with the 4 screws.The extra pair of hands to hold it was helpful. This repair was very easy. It took less than 30 minutes and I saved $300 in repair costs.
Thanks to this web site, I discovered that this problem is very common with this oven.Followed the instructions posted.4 screws under the top of door need to be removed.Pull display cover up and then simply unplug the 3 wire setsRemove old display with the 4 nuts and replacePlug back in and replace and you are good to go.Appears a very common problem and a design problem with this display.
Ordered new display module. Very fast delivery. Removed top anel of oven (5 screws) and display (4 screws) and replaced module. Very easy and fast repair.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.