Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11743805
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
Several days back I found I couldn't get any ice from the ice maker. I was able to hear noise from the ice maker but no ice would dispense. I opened the freezer and removed the ice bucket to find out that the Auger has broken off from it's plastic housing in the back of the freezer. I went to partselect.com to find the part(s) that were broken, it was much easier because of the diagram/images they have for each individual section of the fridge. Parts came quickly and as expected.The replacement of the auger motor is very easy if you follow these steps:1 - Remove the ice bucket from the freezer2 - Unscrew the one screw on the bottom left side of the ice bucket tray (the tray holds the ice bucket in place). I used a small needle nose plier to remove this screw as I was having a hard time with my drill or wrench set. After you've removed the one small screw, lift the tray up and slowly pull towards you. 4 - You'll quickly see that the auger motor and magnetically controlled yoke are connected with a wire harness to the back of the freezer.5 - Gently crimp the ends of the wiring harness connector with your hand and slowly pry away from the freezer. Once you've removed the wiring harness you can remove the entire tray with the parts attached (yoke/auger)6 - Unscrew the auger motor from the tray. You'll also have to remove the auger from the motor else it won't come out. In my case the whole plastic attachment was broken so I didn't have to do this (ie I replaced the ice tray as well). It was impossible for me to remove the auger from the auger motor, not sure why the auger was so tightly attached to the motor - it could be the reason the auger motor broke from the ice tray?, so I had to buy a brand new auger motor and auger (ie Auger Drive Motor Kit). I hope you have more luck then I did removing the auger. If you can't remove it you'll need to buy the Drive Motor Kit (which comes with the drive motor, detached auger and auger washer).7 - Once/if you've removed the auger from the motor and remove the motor from the ice tray, you can proceed with the replacement of motor. 8 - Using needle nose pliers remove the three power connections on the motor (white/neutral?, pink/power?, green/ground, note where the connections were when you removed them because you'll replace them in the same place on the new motor).9 - Attach new motor to ice tray with the four screws, attach the auger and auger washer to the auger motor, attach the power connections back (white, pink, green).10 - Re-connect the wire harness to the back of the freezer11 - Move ice tray back into place, and attach the one screw back to the ice tray to hold it in place.12 - Replace the ice bucket back onto the ice tray13 - Done, you should now get ice!Good luck, I hope this helps. It's easy and you don't have to pay three times this price to replace these ice bucket parts.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Remove ice maker. Remove single screw from under enclosure. Unplug wiring harness from refrigerator. Remove Ice enclosure. Removed metal yoke (left hand thread) with light tap from rubber hammer then removed all screws holding motor assembly and yoke assembly. Reverse the procedure to install components. Plug in wiring harness and install enclosure. Align ice dispenser with metal yoke on enclosure and install ice dispenser.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.