Quick Question!

Have you ever purchased from PartSelect.com before?

11743367-1-S-Whirlpool-WP660533-Surface Burner - 8" - 2600W
11743367-1-S-Whirlpool-WP660533-Surface Burner - 8" - 2600W 11743367-2-S-Whirlpool-WP660533-Surface Burner - 8" - 2600W 11743367-3-S-Whirlpool-WP660533-Surface Burner - 8" - 2600W http://www.partselect.com/Schematics/Maytag/7689.gif

Surface Burner - 8" - 2600W

PartSelect Number PS11743367

NOTE: The manufacturer recommends that you replace the burner receptacle at the same time.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Element will not heat.

Compare At

$54.67

You Save

$9.11

Your Price

$45.56
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 32 reviews What's this?
1-15 of 32
 

54 of 64 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Jonathan from Lilburn, GA

8 inch burner wouldn't come on. Wires shorted out

One screw holds the block onto the stove top. Had to clean out fitting for phillips screwdriver or screw would have stripped because it was old with lots of buildup. Even cleaned out, this screw required great force with phillips screwdriver to keep from stripping. Caution! If you strip it, you'll have to drill it out! The rest was a snap. Cut the old wires leading to the old block (not too close to where wires disappear into back of stove, though!). Strip insulation off both wires and attach with the connectors that came in the kit. Then push the wires into the block, and finally, attach the block back to the stove top (new screw is supplied). Restore power and everything should be fine. One problem: Roper/Whirlpool built their appliance in such a way that when the connector block shorts out, it usually takes the infinite switch with it. So I ended up having to go back and purchase that switch as well (which just so happens to cost twice to three times as much!). If you put it all back together and it still doesn't work, that's probably what happened, so go ahead and remove the knob panel and check that switch (it's right behind the control knobs on the front). You will probably find a burned connector at the back top left or the switch. Don't forget to write down which wire goes where (or just take a picture of it).

Help other customers find the most helpful instructions.

Were these instructions helpful?   

15 of 17 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Mary from Lebanon, CT

1 had 2 large burners not working at all, and was cooking everything on the 2 smaller burners

It was so simple to repair - all I had to do was slide the older burners out and slide the new ones in - it took less than 10 min to complete the whole job! No tools used at all.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

13 of 17 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Rolland from Walla Walla, WA

Receptacle burned out, due to short

This was the second repair of the same problem. I realized this time that there was a poor connection between the burner and the receptacle causing a arch, creating extra heat and burning out the receptacle.
All that I had to do was to cut two wires to the existing receptacle assembly and use the wire nuts to connect the new assembly and one philips screw holds it in place...The kit required me to assemble it first and there were four items to put together. No problem....

Help other customers find the most helpful instructions.

Were these instructions helpful?   

11 of 14 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Scott from Pleasant Valley, CT

Burner was arching or not heating up.

I followed the instructions on removing the existing burner, recepticle, and section of wire. Then followed same instructions for reinstalling above new parts. The instructions were simple and straight forward. The only gluich was that I had to drill out the rivets holding in the old hold down clips. I drilled these out with an 1/8" bit on the burner side off the opening.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 12 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Steve from Mount Carmel, PA

Heating element and socket needed to be replaced

It was very easy, the element is held in place by a point that protrudes from the element's frame through a hole in the stove top. This hole is located directly across from the electrical socket your bheating element plugs into, under the stove top. Push the heating element in towards the socket and the heating element can now be lifted up and out of the burner tray. Remove the burner's reflector tray. Remove the single screw securing the elements electrical socket to the stove top. Lift the stove top up and secure. Remove socket and cut wires about 4 inces from the old socket. place shrink wrap over each wire and wire nut new socket to existing wires. place shrink wrap over wire nuts and heat to secure. reverse proceedure and test.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 11 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Sharon from Phoenix, AZ

Original burners were not working correctly.

I received my ordered in less than a week. It was great. The day I got them I remove the old burners and replaced them with the new ones. It took me about 3 minutes total. I was then able to cook my Christmas dinner with out any problems.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: CHARLES from SOMERSWORTH, NH

Cooktop elements worked intermittantly.

Turn the power off to the unit. Remove the cold element by lifting up and pulling out. Remove the drip pan. Remove the element plug screw and pull the plug up and out of the socket. Cut the leads to the plug as close to the plug end as possible to allow enough wire to splice the new plug in. Strip the insullation back 3/8" to allow for splicing. Install the shrink tube collar on the wire and place one new lead (prestripped at the factory)next to the old wire and place the wire nut provided over the bare wire ends and twist it on until it is tight. Bend the wire nut splice back over one of the leads and slide the shrink tape over it. Heat up the shrink tape with a hair dryer to make it tight over the wire nut connection. Repeat the process for the next lead. Slide the leads into the new socket. Install the socket and secure the the new screw provided. Reinstall the drip pan and plug in the heat element. Follow the same procedure for each element socket replaced. Turn the power back on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: Patti from Burbana, IL

Sparking burner

Followed instructions from previous repair story!!
Pulled old burner out. Unscrewed plug element. Cut old wires back about 6 inches from plug. Attached new part with wire nuts provided and covered with shrink sleeves provided. Attached plug with provided screw and slipped in new element. Works great!!
I want to thank the previous posters for posting their detailed repair stories....without reading those, I may have called a repair service and paid big bucks. Thanks to all previous posters for the detailed information they provided!! PS...The parts arrived in amazingly quick!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: David from Jefferson Hills, PA

Intermittant heating, arcing in the socket

Simple to do. Remove old element, remove screw holding socket, cut the socket wires with 2 inches to spare, assemble the newsocket and wires with heat shrink tubing, strip range wires, apply the wire nuts as instructed and shrink the tubning with a heat gun.

Screw on the socket to the range. Shut the lid and install the element.

The replacemnet screw is thicker than the original one, so you might want to drill out the hole very slightly. I did not but the resistance was high on getting the screw fully seated.

Works great

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Surface Burner - 8" - 2600W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Marjorie from Swanton, MD

Burner would not stay heated had to wiggle the burner to make heat

Replaced with the new burner works like new. Thanks a bunch!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Surface Burner - 8" - 2600W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: james from killingworth, CT

Burners weren't heating

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
  • Surface Burner - 8" - 2600W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Jacqueline from Austin, TX

Electric stove burner was working unreliably

pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools:
Customer: FRANCES M. from GRAND JUNCTION., CO

Broken burner

Unwrapped package. That was the hardest part. Inserted into the little spot on top of stove. Tested. Worked great!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: ROBERT from ARVADA, CO

Intermittant operation of surface burner

I first tripped the power circuit breaker. Then I unplugged and removed the old element. Removing one screw allowed me to remove and replace the mounting clip. This did result in breaking off a small piece of plastic-like material from the electrical housing to which the clip was attached but did not hinder the replacement of the new clip. I inserted the new burner element. The surface burner is now working fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools:
Customer: glenn from ST AUGUSTINE, FL

Burners wasn"t getting hot like they should

i just unpluged the old burner and slideed the new burners in place and they work great now like a new range

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-15 of 32