Quick Question!

Have you ever purchased from PartSelect.com before?

11743345-1-S-Whirlpool-WP63907-Suspension Spring
11743345-1-S-Whirlpool-WP63907-Suspension Spring http://www.partselect.com/Schematics/Maytag/OGHXSQCE.gif

Suspension Spring

PartSelect Number PS11743345

Sold Individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Shakes and moves.
  • Noisy.
  • Leaking.

Compare At

$6.16

You Save

$1.03

Your Price

$5.13
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.8 / 5.0, 24 reviews What's this?
16-24 of 24
 

5 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Socket set
Customer: Thomas from Addison, NY

Tub off center. Upper agitator not driven.

Pop off the softener dispenser. Pull the cover/ seal out of the upper agitator. With 7/16" socket and extesion bar, remove bolt and pull upper agitator straight up and off. dump out old assembly and replace with new assembly. Set back in place and replace bolt. Repair kit comes with good instructions and new rubber O ring for bolt cover/ seal. (thanks).
The suspension spring takes more effort but not hard. with washer laying on face I used a piece of 2x4 to pick up the tub in the direction of the broken spring. Put the new spring through the wire hook loop and snake it through the slot in the frame and you can see how it locks in place. With the 2x4, push the tub toward the new spring until you can hook it through the slot on the tub frame. Done. Parts cost less than an estimate from a service call and I finished the job in 30 minutes, which includes unplugging the power cord, turning off the water and taking off the hoses so I could lay the washer down. Saved the website in my favorites for the same great prices and fast shipping next time.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
  • Suspension Spring
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: WILLIAM from DAYTON, KY

Drum slamming into the back of the washer when sipnning

I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 12 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Russell from Chicago, IL

Out of ballance

removed two phillips screws from control panel. lifted panel to reveal two clips on both sides of machine. used flathead screwdriver to remove clips. tilted whole body up and away. pushed drum towards first spring and removed it . installation was reverse of procedure. did not fix it because basket had rusted at shaft bottom under agitator and put basket out of balance.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Chris from Bonners Ferry, ID

Washer would walk all over when in the spin cycle

I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: Norman from Burlington, NJ

During the spin cycle machine rocks the house

Replaced all of the springs. I put the shell back on and the problem still exists. I thought $20.00 was worth seeing if this would resolve the issue. I don't want to keep throwing parts at it. I noticed some black suit under the machine. I will be buying a new washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers
Customer: William from Mokena, IL

Washer tub off-balance during spin

This washer does not have a removable front panel, so the spring replacement was made from the bottom of the unit, with the washer lying down on its face. This put two of the springs in tension which had to be relieved by propping the tub. The springs had removable bottom clips which made the job much easier.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Suspension Spring
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Wrench (Adjustable)
Customer: ROBERT from ROCKY HILL, CT

Washing moving all the time-lefth-to right all the time.

Pulled it apart,layed it down and looked at it,and chaned the 3 springs. And it is like new again. . . . .

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Suspension Spring
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Stacy from Markle, IN

Tub out of balance on spin cycle. Very noisy!

I the took washer to where I could lay it on its side.
Laying it on its side lets the suspension spring at the top go slack. Making pulling it from bracket easier.
Next , I lifted the tub up with a 2x4 and blocked it with another wood block. This let me have slack in the lower springs.
Of coarse I saved the hardest one (behind the motor) for last. I only swore a little! But got it to come out.
By the way, put in each new spring, before going on to the next one.
The new springs helped a lot, but I ended up ordering the wear pads a day or two later. They were very easy to replace. Just pop the old ones out of the frame with a screw driver. then pop the new ones back into the holes and you are done.
You may just want to buy them both and do it all at once. Saving moving the washer twice!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

63 of 1728 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: More than 2 hours
Tools:
Customer: BOB from NIAGARA FALLS, NY

Tub shacking back and forth

After seeing video it was easy . Took everything apart tub,basket,replaced all springs. Tub wear pads. It took longer because I cleaned eveything,took my time. There was a lot of deposits on tub and outer tub also some rust . Put it all back together all nice and clean . pluged it in put it in spin cycle and the motor just hummed. I than check to see if somethig was stuck no .Pulled motor tested it with out a load and did not work. Motor start winding went. Motor died. 2n one in 7 years. So I fixed that proplem I am a new owner of a Speed Queen washer and dryer .

Help other customers find the most helpful instructions.

Were these instructions helpful?   

16-24 of 24