Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11743155
This lower hinge pin is almost two inches long. It is made entirely of plastic and it is all black in color.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
First I removed the three screws in the top hinge that hold the upper right corner of the door to the body of the unit. Then I just lifted the door off of the refrigerator. I proped the door up just long enough to pull out the old pin (plastic) and put the new one in place. Next I picked up the door and set it on the new hinge, and last I put the three screws back into place. It has taken me about as long to type this out as it did to actually make the repair. The part was also very reasonably priced so I purchased two since this items has been replaced previously.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Replacing the hinge pin itself is really easy. Most important is to brace the bottom of the door before replacing the pin, otherwise the door will drop as the bottom hinge must be removed to install the new pin.A couple of short lengths of 2x4s used to brace the door bottom worked fine. With these in place the door did not drop down after removing the hinge. Replacement of the hinge and pin easy.
Supported door in the closed position to keep door from falling with wood 2X4s. After that it was easy to replace lower hinge.
Cleaned out the door. Loosened the top hinge. Lifted the door off hinge pins. Replaced lower hinge, hinge pin and closer. Put door back on. Tightened upper hinge back down on door. Done. Very easy and door is not that heavy.
This was easy. Removed the plastic cover at the top hinge. Removed the 3 screws at the top hinge. Lifted the door off of the bottom hinge and laid it on it's side. The part that was worn out is the "natural door closer". It looks like this part will need to be replaced every few years, it is made of plastic and was ground down to nubs. Remove the screws holding it down and replace it with the new one. Lubed it up with some WD40 to get rid of squeaks. I also replaced the lower hinge pin, but I don't think that was necessary.
Most of the time was sent to removing and replacing door shelves. Pry off upper hinge cover. Easy, it's only plastic. Remove 3 fastener from top hinge and remove hinge. Lift door off lower hinge. Lay door down on table let handle hang over edge. Remove door closer attach fastener. Remove and replace door closer. Pry lower hinge up and out. Tap new lower hing pin into place. Replace door, upper hinge and hinge cover. Had to replace Door Closer and Hing Pin together; both were worn and needed replacing.
1. mark location of removable baskets in door and remove baskets2. remove three screws in top hinge - save shim under hinge 3. lift door from lower hinge4. remove 3 screws from lower hinge bracket and remove bracket5. install lower hinge bracket with 3 mounting screws6. install lower hinge pin in bracket7. clean upper and lower hinge holes in door8. lubricate upper and lower hinge pins with grease9. place door over lower hinge pin - the magnetic seals will hold it in place10. install upper hinge bracket with 3 screws11. install baskets in doorNote: The plastic piece on the bottom of the door that mates with the hinge pin and provides a cam action should have been replaced at the same time.
Removed the food out of the fresh food door. Removed the top hinge cover, removed the 3 nut screws on top. Lifted the door off of the bottom pin. Set the door to one side. Removed the lower hinge pin with a screw driver and replaced with new product. Lifted door back onto lower hinge pin, secured the top pin hinge with the 3 nut screws, replaced the top hinge cover and placed food back into the door. Done in less than 15 minutes.
Removed the top hinge of the door. Lift door off the lower hinge. Unscrewed the "natural closer" from the bottom of the door and replaced with new part. Pulled off the lower hinge from the lower bracket and replaced with new hinge pin. Replaced and realigned door. Piece of cake!
Place two 2x4s, stacked on each other on floor parallel and close to refrigerator, leaving room for socket handle and extensions to three lower hinge bolts. Placed 3 foot 2x4 at right angles on top of the parallel stack of 2x4s, with one end under right hand refrigerator door. Placed 20-30 lb bucket of rice on other end of 2x4 to exert upward pressure on door, raising door bottom off of hinge pin. Removed three hinge screws. Replaced Natural Door Closer and Lower Hinge pin. Screwed three hinge pin screws back in. Removed fulcrum.
Simply remove the ref door bracket at top and remove the door from the bottom hinge pin...Then replace the lower hinge, hinge pin and door closer... Reinstall the door and adjust for level...This took only 25 min to fix.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.