Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11743046
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
First off, I must give thanks to Partselect.com for excellent service. They had the parts I needed, a Diagram of how the parts should go into the Dishwasher, and shipping was very quick and reasonable priced. Thank you Partselect.com.After dinner we heard our Maytag MDB5100AWW dishwasher start grinding during its wash cycle. Needless to say we found this quite concerning, as this is not what a healthy dishwasher should sound like. After fiddling around with it, I started researching the issue and found Partselect.com where it was stated the “Discharge Housing Assembly (Discharge Pump Housing)” was a common failure point. After disassembling the “Pump and Motor” section of the dishwasher, it was confirmed that the Discharge Housing was indeed broken. Since this Dishwasher is over 8 years old, I figured that I might as well replace a few other parts as well, since I'm in there working on it.Following the blow-up image of the Pump and Motor picture;Unscrew part 34Pull out part 1Lift Part 2, which is attached to part 36Unscrew part 5 (6 of them) from part 4, be careful not to loose part 3, sitting inside part 4Lift out part 6 and 7Unscrew part 8 and lift out part 9Unscrew part 27 (three of them) and lift out part 11The bottom plate of this part is the broken part.Now, since we are in here replacing a part, we might as well replace a few other parts and give this dishwasher a little longer life. I opted to replace the following parts as well, being that my dishwasher was over 8 years old and the gaskets were showing some age.Part 4 – Pump Cover and Secondary Filter Assembly; I replaced this part because food often gets caught inside the filters and will throw off the balance during a wash or rinse, thus putting premature wear on bearings and o-rings. My filter had a bunch of food on one side, and the only way to remove the food was to slit open a section of the filter, thus damaging the filter screen.Part 37 – O-Ring that goes inside the Pump Cover and Secondary Filter Assembly. O-rings are rubber and do wear with age. My dishwasher didn't even have this o-ring; now it does.Part 3 – Lower Spray Arm Seal; I noticed when pulling these parts out that the hard water in our living area was making these somewhat brittle. When ordering these, get two of them, as the picture indicates. If you order one, the package only contains one, and not two was the image shows it should have.Part 11 – Discharge Housing Assembly (Discharge Pump Housing). This is the part that is making all the grinding noise. The new part will show that it is built a little differently. It appears that Maytag figured out the weak design of this part and made the replacements stronger.Part 17 – Even though I ordered this, you don't need to order this part if you order the Part 10 kit. The part 10 kit will include this o-ring. Because its an O-ring, I replaced it; as stated above, o-rings do breakdown.Part 25 – Pump Gasket; This part should really be called the Pump Housing Gasket, as it isolates the Pump Housing bucket and the Dishwasher tub. I bought this because my original gasket was looking pretty nasty and was coming apart.Part 10 – Seal Kit (Motor/Pump) (Motor/Pump Impeller and Seal Assembly), this kit includes several components that if purchased separately would easily be twice the cost of this kit. Again, seals and Motor Pump seals are a good thing to replace when needing to do work inside the dishwasher.Continuing on from the previous dis-assembly list;Unscrew part 12 and remove part 14, 15 and 16.Unroll part 17 (o-ring) and remove part 18.Unscrew parts 19 and carefully remove part 20, being VERY careful to not loose part 39.Lift out part 22, which will include the bearing inside of part 22.Pry out part 24 with a pick (the replacement is in the kit of part 10).To remove part 25, you must Remove part 12 of the Door Assembly (see the Door image) to reach the motor element.Next unscrew part 14 of the “TUB” i
Help other customers find the most helpful instructions.
Were these instructions helpful?
removed lower spray arm and the 6 torx screws that hold the pump cover and secondary filter housing. Removed it and the filter. Removed the pump housing and removed the impeller nut with a 5/16 nutdriver. Removed the old impeller and put in the new one. Replaced the parts in reverse order.
Our first effort was to replace the lower washer arm that had splits in the sides of this plastic part. While this increased the water pressure in the wash cycle some it was not enough to adequately wash the dishes. We read that someone else had to clean out the filter which was below the lower washer arm assembly. Thus, we took off the loweer arm assembly by screwing off the hold down assembly in the middle of the arm. We then took off the pump cover by removing the 6 screws that hold it in place with a #3 metric allen wrench. When we took of the cover we could see that the pump filter was so covered with deposits that it was not letting the water through to the pump. Rather than spend hours trying to clean the filter and pump cover we decided it was easier to repalce them. Thus, we ordered the parts and replaced them. The dishwaster is now working fine. We appreciated the information that others had shared that helped us find and fix the problem.
After removing parts, cleaned both upper and lower spray arms, blew out lead to the upper arm, and started to install the new parts.Unfortunately, the Pump Housing Filter was still cold (freezing weather during shipment and left at the front door) and when I started to bend it into shape it broke in two places. So I tolk the old filter and some Lime away and slowly cleaned it with soft brush to open 95% of the holes.Once ready it was installed along with the other new parts and the dishwasher works very well.Simple homeowner repair.
The repair was very involved, but from previous experience cleaning the dishwasher, it was worth not having to buy a new one. I removed all of the lower parts down to the motor shaft. That process is tricky, but if you do it methodically, and slowly, it is not too bad. The real problem wash the scum that was left behind by the soap used in the dishwasher. After removing all the parts, I ordered the parts I could not clean, and cleaned the parts I could. I figured out that the door was leaking because of the soap scum buildup on all the parts, causing the water level to raise faster than it could be pumped out. After I received the new parts, I simply put everything back together and it works better than ever now. I used the parts layout on your website to help in aiding me to put everything back correctly. I am very appreciative that I can get parts easily through your website, and not have to hire a "service technician" to come out and do the same thing, for the price of a new washer. Thanks!
Removed top retaining piece by turning clockwise to remove spinning spray arm from bottom assembly. Removed the 6 retaining screws from the primary screen pump cover and lifted up. Removed filter and the four pronged piece that spins with the filter. Removed the 3 hex head screws that held the secondary filter assembly & pump cover in place. Removed center screw that held the bottom black plastic piece just above the secondary filter bottom. Inspected the cutter, then started reassembly in reverse for the replacement of new parts and filters.
The top and bottem spray arms plus the secondary filter located on the bottom of the dishwasher were 80% blocked with dishwasher soap which would not allow water to rinse the dishes completely.The upper spray arm had fallen off, so I was able to quickely replace it with the new arm and clip by simply inserting the clip into the spray arm and pushing it into place. The lower arm came off easily by turning the large knob on top off it and pulling it off. After removing the arm I was able to access the three screws that release the secondary filter cover. The screws required a set of star sockets to turn them.I then put the filter cover on and replaced the screws. I placed the lower arm assembly back on and ran the dishwasher. It worked like new again. The photos and descriptions in the parts catagories made it very easy to find the correct parts that I needed. I highly recommend Partselect to anyone who is a do-it your-selfer! Jim Three Rivers MI
I discovered that, except for the central tower, all the spray holes were all plugged with I took to be calcium deposites . Using the parts diagram located on this web site, I removed parts. All parts can be removed either by hand, nutdriver or small wrench however you do need a star drive (simliar to an allen wrench) to remove the Pump Cover and Secondary Filter. The Lower Spray Arm unsnaps from the Pump Cover and Secondary Filter. I laboriously removed the deposits from each part down as far as the support filter. The upper spray arm can be removed by unsnapping the hub. the Pump Cover and Secondary Filter is a closed unit so. I purchased a new one. The process is very labor intensive. Next time I am going to consider purchasing all new parts or calling a repair man.
Troubleshooting took a bit of time but I finally narrowed the leak down to the lower pray arm that had separated along the seam. It was spraying water directly at the door seal causing the leak. After the fix, the leak was gone, dishwasher was quiet again, and dishes were clean again.
I TOOK THE INSIDE PARTS ABOVE THE MOTOR APART AND TRIED TO CLEAN ALL THE CALCIUM AND MINERAL DEPOSITS THAT WERE PRVENTIN WATER FROM GETTING THROUGH. THERE WAS A LOT OF CALCIUM. MOST OF IT i WAS ABLE TO CLEAN AFTER A LOT OF SCRAPING AND SOAKING IN VINEGAR AND CLR. THE VINEGAR WAS THE MOST EFFECTIVE OF THE TWO.i BROKE THE FILTER GUARD WHEN I TOOK IT APART. I SHOULD HAVE CHECKED ONL.INE BEFORE i START IT. THE SECONDARY FILTER ASSEMBLY WAS TO FAR GONE DUE TO MY MISHANDLNG AND HEAVY DEPOSITS INSIDE THE FILTERS. PUTTING IT BACK WITH THE NEW PARTS WAS EASY BUT I HAD TO SUBSITUTE SCREWS BECAUSE THE ORIGINAL ONES WOULD NO LONGER HOLD TWO PARTS TOGETHER. THE PARTS WERE LEAKING TO MUCH WATER. ONCE I HAD IT BACK TOGETHER THE SECOND TIME IT WORKED FINE. HOWEVER I HAD REALIZED THAT THE O-RING WAS NOT MISSING (MY BAD EYES DID NOT SEE IT IN PLACE AND SO I THOUGHT I HAD LOST IT). i EMAILED PARTS SELECT FOR A RETURN AUTHORIZATION BUT NEVER HEARD BACK FROM THEM. MAYBE I NEED TO GIVE THEM A FEW MOR DAYS. THE O-RING COST $3.76 AND MY WIFE WILL NOT BE HAPPY TIL I GET THAT BACK. PARTS SELECT DIAGRAM AND PARTS PHOTOS AND ANOTHER WEBSITE WERE A BIG HELP..
Pulled both dish racks out then the spray arms. From there took everything else out down to the top of the motor. Replaced both spray arms and anything that a filter or a screen in it. Got everthing back together and ran the unit full of dishes with no issues at all.
replaced wiyh new parts
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.