Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11742849
This outer door handle is half of a two piece door handle assembly. It is all white in color and is made entirely of plastic.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
removed trim around inside of door with putty knife.disconnect latch spring with needle nose plyers.remove two handle screws.remove small screw on handle to separate outer handle from inner handle.replace outer handle and assemble with inner replace screw.connect handle in door snap tim back into place
Help other customers find the most helpful instructions.
Were these instructions helpful?
My son-in-law took the handle off. We saw the problem (Maytag put two tiny plastic posts that crack about once a year. This was the 2nd replacement in 2 years.) When the new part came in my 15 year old grandson put it on easily. This is a no-brainer!
I pondered getting both the inside and outside parts but went with the outside only. Prying the gasket loose went very easily, and removing the latches went easy too (to expose the bottom screw. I found the inner handle base broken but glued it together, not worrying too much because the real attchment to the door is done with the outer handle screws. I can see why the handle broke in the first place because the screws went in with a lot of torque necessary. I suspect that this weakened the posts so I lubricated the screws and backed them in and out so as not to stress the posts. I think all that is necessary is the outer handle, if you want to save some money. Everything snapped back into place easily and it is done after listening to the wife complain for almost 6 months. Part Select is a great site for appliance repair.
My son took the door sealer off. It just pulls off easily. Then with screw driver took out the screws and put on the outer part of handle and replaced the screws and bracket. Took less than 30 minutes after we found how to do it.
remove inner door frame,remove screws holding inner and outer handles reuse inner handle,replace outer handle as needed reinstall inner door frame.
1. Open Door2. Use Putty Knife and and carefully separate outer door frame from inner door frame by sliding the putty knife all the way around the frame from the inside3. Remove the old broken handle. You should use a pointy nose pliers to take hold of the handle screws once you have then loose...4. Install new handle, Make sure it is seated flush in the door frame, then tighten with two screws (use the pointy nose pliers to get them started . .very tight space to work in)5. Snap on outer frame.6. Your done! Dave
Found info on how to replace handle here. Couldn't have done it without that information! We popped out the black trim on the inside of the door and removed the spring to access the bottom screw. From there it was pretty much easy to see where ever thing fit. Had difficulty getting the tabs clipped in the front of the door.
I received the door handle in 2 pieces along with one screw to put the two together. 3 days later the 2 screws to attach the handle to the microwave door showed up so I could finally put the handle on. I was amazed that I had to purchase each piece separately and that they pieces were shipped in two deliveries.
Separated the inside panel on the microwave door, removed the screws from the old door handle and utilized them to install new door handle. Access to the screws was a little tight thus the "a bit difficult" rating.
removed screws from the old handle (this took the longest amount of time - 5 minutes, and required a needle nose pliers and a screw driver). Replacing the handle took 2 minutes to screw the handle to the door. Very easy!!
Removed the door from the oven by lifting and unhooking from appliance.With a small putty knife remove the snap-in ring from the inner door.This will expose the screws that hold the handle.Replace then put everything back in reverse order.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.