Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11742773
This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to.Followed other people's excellent instructions. Clean out all the dust bunnies. Schematics were a great resource. Those and the prices made me a repeat customer.The shaft of the Idler Lever wheel was the cause, but decided, since I had it apart, to spend a little more money and replace both Drum Support Rollers and the Roller Bracket and Shaft Assembly. They showed some wear, and the parts were very inexpensive. Make sure you have snap ring pliers with prongs that are smaller than the standard 0.40 to save some aggravation with the Drum Rollers. $5 tool. Total parts were less than $60. Probably saved $150+ in labor. Quieter than ever now. Thanks!
Help other customers find the most helpful instructions.
Were these instructions helpful?
Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all.
I am a widow. Had to pay for labor. He said it was motor. I said I would think about it. I looked on line at your site. Found symptoms that pointed toward idler pulley wheel with bearing, etc. Your site said: ZERO PERCENT CHANCE LOUD SCREECHING WAS MOTOR! So I ordered all parts above. I called repairman to return; he assured me he tried it enough to be assured it was motor bearings. So, I placed another order with you for a motor. Repairman just installed motor, screeching is gone! We installed the belt, pulley, etc..few of the above parts since dryer is old. PLEASE UPDATE YOUR WEBSITE TO INCLUDE MOTOR (BEARING) AS POSSIBILITY FOR LOUD SCREECHING.
I removed the lower front panel, which is held in place by two screws at the very bottom. I found pieces of the worn out brackets in the bottom of dryer. I then located damaged brackets bolted under front of drum at about 4&8 oclock. each bracket is held in place by two small bolts from the back side. The bolts for the new brackets go back in from the front, which eliminated the problem of stripped out holes. It is helpful if someone can reach indryer and hold up front of drum while you are starting bolts in brackets, I found that the kid standing closest worked great. The exploded view parts list was great for finding what I needed. My old dryer works great again and it is as quiet as a new one. This was $24.00 that was very well spent.
Squeling from inside dryer. To Fix-Pry dryer top cover off by popping cover off the two fastening clips located at about 3" inward from the two front corners. A screw driver at these two locations is easily inserted between the top cover and front panel. Next remove the two screws on the top inside of the driver approximate size 5/16 inch. Pull the top of the front panel outward and then note how the lower portion clips into the fram, lift the front panel off the clips and roll it to the right. Remove the 4 screws and bulkhead.Draw a picture of how the belt wraps around the drum and idler. Also note the belt orienation on the drum. Roll the belt off the idler pully and reomve the drum.Replaced Idler asembly by first removing the tension spring and lastly the retaining bolt.Reinstall everything in reverse order. Can be a bit tough getting the belt around the idler and motor pulley however this is managable. My machine runs great now!Once again Parts Select comes through with great delivery, perfect fit, good pricing, accurate parts list. This is my third purchase and I have been 100% pleased. By far the best on line service I have ever experienced.
Parts that were recommended for the noise issue were spot on. Instructions were very helpful and made the job go very smooth. Replaced the belt, rollers don't forget to order (2) felt pad and idler pulley replaced. The part suggestions for the heat problem did not fix the problem. The burner flame would come on for 2-5 min. then go off. A few min. later the burner would try to ignite but would not start. The igniter would get cherry red but no activation. I end up replacing the coil kit. Turned off the gas removed (2) screws and wala done 5 min. and it fixed the problem.
removed the front panel and the drum panel cover.replaced the guides and the felt pads and re-assembled.
Removed front panels and swiveled lid upwards. Loosened tensioner, removing belt and then carefully extracting the drum. Replaced 2 drum glides on underside of front panel. Next 2 rollers, which appear to unscrew, but do not do so. You must remove the retaining ring (surprise! ...and 2 screw drivers later). This was the longest and most frustrating part of the whole ordeal. Then just reverse the process for reassembly. This was my first electric dryer repair and it really wasn't too bad. Online docs I found were somewhat helpful, but really luck and perseverance. I did save probably $300 in replacement costs, which is quite satisfying. .
Loud squealing noise coming from the idler pulley. The pulley was not spinning freely on the shaft of the idler pulley lever to the point of putting a groove in the pulley and damaging the belt. To fix the problem replaced the belt, idler pulley, and idler pulley lever. Because I had the dryer apart also replace the following items. Drum support roller and drum slides.
I opened new parts and stcuk a felt pad on each glider and put one of my 10 lb. weights on it for about 1/2 hour to help it stay in place.Then removed top panel and then the front..There are three phillips screws that hold the lint catcher in place inside the barrell. Then remove the 4 total bolts to remove Glide Brackets.Mine was so worn down that the barrel had rubbed alomost all the way through a bracket. Once felt pad was firmly set, i attached glider into bracket and installed them.Put everything back in place and started up..and it was running and sounding like new...i paid 27.00 for parts and saved big time compared to what a service shop would have charged me. The shipping was super fast and with my wife and i having 9 children in the house it was a life saver for us.
Idler was the noise source. Drum support rollers were failing also. I almost spent $500.00 on a new dryer, glad I replaced the parts instead. Sounds and works like new. Watch the video,its very helpful. Thanks Parts Select. You should advertise your services on TV or radio. I am glad I found you.
I removed the bottom panel, then the larger front panel that includes the door. After that, removed the top 2 screws so that the top would swing up (but not lift off). After that, I removed the front "bulkhead", and the drum. Then it was just a short matter of sweeping everything out, and replacing the parts one by one. Most came off with a socket, or snap ring pliers. Pretty obvious at this point...Be sure to label any wires - I removed 5 wires all total, and wrote down the colors and where they went.It's great to have help when working with the drum. BTW, you CAN replace the belt without taking out the drum, but you better have strong fingers to move the belt tensioner and slip the belt on it - all with one hand. I did it, but that was the least "fun" part....
1st of all my dryer came apart differently than your video showed. I had to remove the lower front panel (2 5/16 screws) then remove the upper front panel (2 5/16 screws)and the spring clips mentioned in the video, then the top with two more screws. After that the removal of the front drum support assembly was as shown in the video. I then loosened the drive belt, removed the drum and the external grip ring securing the idler pulley. The pulley rotated very hard since the shaft and bearing were partially seized. I cleaned the shaft before installing the new pulley. When I initially took the dryer apart to see what the problem was I noticed the front drum guides were showing wear so I ordered and replaced them and the felt pads just to prevent problems in the near future.
removed the front panels, removed the drum, then with with the ring pliers removed the worn out rollers and roller brackets and replaced with new. Vacuumed the inside and replaced the drum and panels.
I took the bottom on the dryer off, then took the assembly that held in the drum. Then I took the drum out. replaced the bad parts, and put everything back together.I turned on the dryer, and presto.. no more grinding noise.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.