Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11742322
This rubber tube carries water from the upper spray arm manifold to the receiver of a dishwasher. This thin walled tube can become brittle over time and crack. If it does, it will lead to poor cleaning quality of the dishes on the upper rack, and you will need to replace it.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
we used hot water to soften the ends of the tube and then slid it onto the two ends of the parts in the dishwasher. It did take a little bit of "push" to get it on one end, but nothing we could not handle. I would say anyone with common sense and willingness to fix something them selves would have no problem. I would like to say the part I ordered was of good quality and saved me a lot of money.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Pulled off old tube and slipped on new one.
Rubber Water Delivery Tube and Upper Spray Arm Receiver had worn out on my 24+ yr. old Kitchen Aid Dishwasher. First time anything every had had to be done to this machine. It has been a work horse and still works great. The above parts had simply worn out. I found this site online and sent for the parts. My husband replaced them and followed the instructions of greasing the parts when replacing them. The job was done in minutes and the washer is working fine again.The parts were shipped promptly and we had them in a matter of two or three days. Great experience with this company and will use again if the need arises.
Took off old hose. It practically fell off.Used a spoon to widen the ends of new hose and twisted on one end, then other end slipped on. Done!
Loved how easy it was to deal with you!Part was clearly pictured and came immediately!Very satisfying to fix it so easily.Wondered why we waited so long!
Our diskwasher is over 20 years old. The manufacture did not even list the model anymore. Googled - Kitchenaid parts old. Found your site and order the part on Sat. night. It arrived on Wed. Installed as follows that night. After reading other reviews on how the job went and seeing that people had problems getting the tube to slide on the outlets I decided to take the rack completely apart so as to have unrestricted access to the connections. Would be easier to work the tube on to them.First I removed the top rack by releasing the two retainers on the upper rack side rails which hold it up. Then I turned it with bottom up and released all of the plastic clips that held the bottom half of the rack in place. If a clip breaks you can use a nylon cable tie to replace it. Then I took out the screw that holds the metal water bar in place and removed it. Then I took out the screw that holds the plastic part that the water bar was mounted on off. Then with the outlet where the tube was to be mounted not connected to anything it was easy to slide the tube on it. I then was able to slide the tube on to the bracket at the back of the rack. Had to use a screw driver to help get the tube over the round outlet. Then worked it on to where it should be. Reassembled the top rack and put it back on the side rails and washed a load. It worked just like it did when it was new. Saved a service call $75.00 and only took about 30 minutes working at a slow pace. Love it when everything works like it should.
I removed the old hose, I lightly coated the id of the new tube with vasoline, both ends, and then heated the oblong end with the hair dryer to soften it and it slid on with litte force. The round end installed without heating.
So easy I could do it! I pulled the old tube off (after having dirty dishes for weeks and not realizing it was because of a hole in the hose. When I told my husband I was going to call a repairman, he suggesting ordering the part on line and doing it ourselves - no reason not to! Piece of cake!
I removed the rubber water tube before ordering the part. After receiving the part it took less than 2 minutes to replace the part. Now the dishes are clean!!
I pulled off the remains of the old tube and simply slipped the new hose on by hand. Easy as pie!
Slipped old one off slid new one on . Took about one minute. Held well and is washing so much better now.
slid old tube pieces off slid new hose on
removed old hose slid the new one on. Easy one minute job.
Pulled off old tube, applied small amount of lubricant to each end of tube, then just pushed ends together. Slide right on, attached new support and in less then five minutes, fixed. Dishwasher running like new.
Our old Kitchenaid Dishwasher was not getting the glasses on the top shelf clean. I looked and found the tube running to the washer arm under the top basket was split.I replaced the tube. First I put dish soap in the ends of the new tube, so they slipped onto the other parts with only moderate force.Now the dishwasher is making the glasses in the top basket clean again.Regards,Bob
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.