Quick Question!

Have you ever purchased from PartSelect.com before?

11742271-1-S-Whirlpool-WP40111201-Multi Rib Belt - 93-3/8"
11742271-1-S-Whirlpool-WP40111201-Multi Rib Belt - 93-3/8" 11742271-2-S-Whirlpool-WP40111201-Multi Rib Belt - 93-3/8" 11742271-3-S-Whirlpool-WP40111201-Multi Rib Belt - 93-3/8" http://www.partselect.com/Schematics/Maytag/58910.gif

Multi Rib Belt - 93-3/8"

PartSelect Number PS11742271

At 93-3/8" inches in length, this dryer drum belt from Amana has five ridges. It is all black in color and is made entirely of rubber. A flat belt, it is 3/8 of an inch wide.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not tumble.
  • Noisy.
  • Takes too long to dry.
  • Will Not Start.
  • No heat or not enough heat.

Compare At

$24.00

You Save

$4.00

Your Price

$20.00
Order within the next 1 hr and 27 mins and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 95 reviews What's this?
91-95 of 95
 

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Maurice from East Falmouth, MA

Broken belt on drum

removed front of dryer, replaced old pully and put on new belt.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Scott from Hawthorne, FL

Dryer had no heat

I pulled the heating element loose and layed it on the floor so I could see if the elements were heating. This required totally disassembling the dryer from the front including removing the drum. Then I bypassed the door switch so the dryer would run disassembled. Then plugged in the dryer and turned it on. Heating coils did not glow... Hmmmm. Put a meter across the two thermal switches mounted on the element assembly to find one of them was open. Ordered switch from PARTSELECT; ordered a belt too while I had it apart. Parts came very fast and reassembled with new parts. WORKS LIKE A CHAMP!!! Thanks Partselect!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Thomas from Norristown, PA

Gas dryer, would only work when it felt like it.

Make a long story short, dryer was on fire from lint in the bottom of it. burned up some wires & other parts. it was easy to repair the wire & replace the parts every thing worked out fine. REMEMBER TO CLEAN OUT THE LINT IN THE BOTTOM OF THR DRYER not only the lint filter or this could happen to you.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

20 of 604 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers, Socket set, Wrench set
Customer: Dan from Newfield, NY

Dryer wouldn't rotate the drum.

Removed the screws holding the bottom to the sides (but after taking it all apart, I think I could have done the repair by just taking the front off :-(.
Removed the screws holding the front to the sides. Noted the wiring (three wires go to the front door switch). Removed the wires from the switch (they are quick connects, so no tools necessary). Removed the front. Pull the drum out.
Disconnected the spring from the idler pulley lever. Removed the bolt and nut holding the idler pulley lever assembly to the bottom. (The old pulley had basically frozen in place which caused the belt to break). Put the new washers, wheel assembly and retaining ring on the new idler pulley lever. Bolted it back in place. Connected the spring. Put the new belt around the drum and slid the drum into place. Put the belt around the motor pulley and past the idler wheel (make sure it is on the correct side so this takes up the tension). Put the bottom screws back in. Connected the wires back up to the front. Put the front in place. (Make sure that the drum is properly seated in back so the front goes on and the drum will turn). Put the front screws back on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

45 of 1298 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Socket set, Wrench set
Customer: russell from anamosa, IA

Would run but would not heat

removed front cover and top took drum out remove heating unit replced limit switch and fuse reinstalled installed new idler put new belt around drum installed drum replaced glides put top back on and front cover . then replaced boosting heater witch is on the blower also cycling thermostat

Help other customers find the most helpful instructions.

Were these instructions helpful?   

91-95 of 95