Quick Question!

Have you ever purchased from PartSelect.com before?

11742244-1-S-Whirlpool-WP40015401-Tub Seal
11742244-1-S-Whirlpool-WP40015401-Tub Seal 11742244-2-S-Whirlpool-WP40015401-Tub Seal http://www.partselect.com/Schematics/Maytag/56490.gif

Tub Seal

PartSelect Number PS11742244

This seal helps prevent any leaking around the transmission of washing machines.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Noisy.

Compare At

$89.28

You Save

$14.88

Your Price

$74.40
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.2 / 5.0, 3 reviews What's this?
1-3 of 3
 

45 of 58 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Customer: Donald from Glassboro, NJ

Washer made loud noise on spin only

Removed agitator, inner and outer tub, balance springs, motor assembly,transmission to get to bearing and seal in tub bottom.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

21 of 24 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Customer: Bruce from Springfield, MA

Very noisy in spin cycle.

Disassembled top and front of machine. Removed agitator cap, removed agitator by removing center bolt. Removed tub top ring, removed balance springs, removed inner tub drain tube,removed shaft nut with channel locks, removed 7 bolts from underneath holding inner tub with 5/16 ratchet. Removed inner tub. Removed bolts holding outter tub, removed outter tub. (rock back and forth to break up old detergent etc... to remove). W-D'd the locking nut after cleaning lint, detergent etc...,used short steel bar and hammer to loosen retaining nut with "L" shaped ears. (it is all one piece and the whole thing turns off, counter/clockwise removal).Remove bearing assembly, clean and install new, remove bearing seal from tub, clean and install new. ( used silicone caulk as additional seal, let set 24 hrs.)Re-assemble in reverse. Runs like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 22 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: DONALD from CRYSTAL LAKE, IL

Growling noise on spin cycle, tub leaking

removed front, top & loosened side covers, removed agitator, removed inner drum & removed outer drum. had to release balance springs, it is a good idea to silicone in the new seal in the drum. this will prevent future leaks. removed lower plate containing the bearing & replaced. re-assembled in opposite order. i gave the silicone a day to cure before use, it works fine now. they say you need a special tool to remove the nut for the drum. i just used a pair of channellocks & tapped the handle, & it came right off.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3