The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool, Kenmore, Inglis.
Part# WP3954071 replaces these:
AP6008934, 3954071, 3954071R, 3954717
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 5 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Timer would not advance
First I watched the "how to video" that corresponds with the part I ordered on the Parts Select web site. The instructions given in the video were so clear and complete that the job was incredibly easy. Parts Select makes appliance repair so easy that Im willing to bet that even the "May Tag" repair man becomes more lonely
David from Clear Lake, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
18 of 22 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
After filling, did not drain, spin, or timer advance to next cycle
1. Removed wet clothing, evacuated water using Python No Spill Aquarium Maintenance System. No mess or water on the floor. 2. Turned off hot & cold water supplies, and unplug unit before moving. 3. Removed unit water supply hoses, and moved unit. The drain hose remained attached while moving
... Read moreto prevent spills. 4. Removed unit from laundry room, and took to the garage on a dolly.
Took out two screws on back of top consule. Lifted consule up and over to expose timer and wires. Removed two screws holding timer. Undid three electrical connectors. Removed timer. Put in new timer and plugged in connectors. Replaced screws and walla. Working fine. Thanks PartSelect!
Wayne from Hnedersonville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wash cycles not moving forward
First UNPLUG THE WASHING MACHINE. Then unscrew the knob and then pull off the bezel (with the arrow on it). Then remove two screws alont the top-back of the unit. Then the two screws located at the base of the control panel section (about six inches from the top - in the back). The cover slides off to expose the timer. There are two
... Read moremore screws on the front (under where the knob was located) that hold the timer in place - they need to be removed. Then pull out the three wire harnesses (I saved the small one for last since it was the hardest to remove - I needed a small screw driver to push down the small plastic latch). Switch out the old timer for the new one and reverse all the steps.
Read less
Richard J. from South Huntington, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer would not function in all cycles
Removed time knob and dial. Removed two screws hoding Console. Lifted Console up and laid it back. Removed two screw holding timer to control bracket. Unpluggd timer connections. Plugge connections into new timer. Replaced two screws holding timer to control bracket. Placed Consel in positon and replaced screws holding console to ba
... Read morese. Replacd timer knob and dial. Tested wassher through cycle.
Read less
James from Cherry Hill, NJ
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
5 of 11 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brad
February 4, 2018
Push pull timer control when pulled out and then pushed in we hear a hum and then it will either work or does not start the function ie..wash, rinse, spin.. when we leave it alone for a few minutes it works. safe to assume the timer needs replacing? do you guys sell the part?
For model number LSN2000JT1
Hi Brad,
Thank you for your question. We do sell the timer for your washer. The part number listed under your model number for the timer is PS11742075. Based on what you described this may be the issue. Before replacing it I would check continuity of the one you currently have with a multimeter. There are some other parts that you will need to check to see which one is causing the issue as well . You will need to check the lid switch, the direct drive motor coupling and the lid strike. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Brad Busleta
February 9, 2018
Thank you very much for your help.. this is the part number for a push pull timer for my Whirlpool ultimate care imperial series washing machine. i removed the timer but i'm not 100% sure that it's the problem. is there a way to check the continuity with it off the machine. after emailing you with the symptoms of sounded like this is the problem. but i figured i'd cover my bases. once again i really appreciate the help! here's the part number. also is this a stock item? part# 3954071
For model number Whirlpool washing machine
Hello Brad, Thank you for your inquiry. You can test the timer with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!
Was this helpful?
Thank you for voting!
Terry
January 21, 2023
Whirlpool washer imperial series ultimate care II. Knob just spins and does not advance to different settings. Can it be fixed without buying a complete timer, manufacturer part 3954071?
For model number Whirlpool washer imperial ultimate care II. Around 2003
Hello Terry, Thank you for your inquiry. You can check the knob to see if it is cracked inside, but if it is the shaft on the timer that is broken, then you would have to replace the timer. To provide you with the correct part number for the knob, we would need the model number of your washer and have provided a link on where to find it. We hope this helps.
Hello the timer number is 3954717 do you have this part
For model number Kenmore
Hi Steve, thank you for reaching out. The part number you are requesting has been replaced by the manufacturer part number WP3954071, and partselect number is PS11742075. We hope this information helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
