Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11742049
This agitator comes with the 4 agitator dogs (cogs) and top mover. The cap is NOT included with the agitator.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Removed top cap and one nut from agirtator then removed complete assembly. Replaced new assembly nut and cap.
First I removed the top of the agitator and then used a socket and ratchet to unscrew the bolt and put the new one on and tightened up the bolt, real easy.
first I removed the fabric softner and water seal from center of agitator, then I removed the bolt holding it on. All I had to do then is install new agitator with old bolt place water seal and fabric softner container back on and start washing clothes again. Very simple.
First I removed the fabric softener dispenser. I removed the inner cap seal and agitator retaining bolt. Then I firmly pulled up on the agitator to remove the complete agitator assembly. I replaced the inner cap seal and installed the new agitator bolt with rubber washer. I placed the new agitator assembly on the drive shaft and tightened the bolt. Lastly I installed the inner seal and the fabric softener dispenser. The total time spent was around 10 minutes.
First I removed the fabric softner dispenser. Then I removed cap took screw out removed agitator asseembly put new one in then I put screws back in.
First repair was easy, remove center bolt, pull up on agitator and replace entire unit as one piece, replace bolt and liquid dispenser. Second repair was more difficult in that I could not immediately find the release to remove timer control. After removing 5 screws unnecessaryily and studying unit more closely, tried prying up on little tab that has a "+" symbol on it that locks into a little hole. While holding up on that tab, slide timer unit sideways and unit falls out of washer panel. Simply slide the new unit in and it locks in place.Also the directions to remove the knob were convienently printed on the orginal and replacement timer, but an ARROW pointing to the black tab on rear of the timer control would be helpful as I mistook the tab to be on the front side under the knob from studing the replacement and tried to pull the smaller inter knob off in order to push it in to release the larger outside knob portion in order to disconnect the timer. No harm done, eventually figured it out, but it still didn't fix the problem. As the washer will EVENTUALLY go in the spin cycle without picking up and dropping the lid, I'm assuming the lid switch is defective, although it appears to work otherwise. Any other possible soulutions appreciated.
Although this was listed as 'a bit difficult' and talking a bit longer than normal, this was because the agitator cap had leaked, and over time the agitator bolt had become completely rusted such that a socket simply couldn't fit. Due to the tight confines, I also could not get a needle-nose vise-grip to hold on to the nut, so attempted to drill out the bolt. This ended up being a problem, but it turns out that drilling AROUND the edge of the bolt and through the edge of the plastic allowed me to remove the top of the agitator, which then allowed a normal pair of vise-grips to be used to remove the bolt. Once the bolt is removed, everything simply fell into place, and the overall job 'should' have only taken a couple of minutes and been 'really easy', except for that rusted-out bolt.
1. Remove Top Cap.2. Remove Seal Cap.3. Remove 7/16 Bolt4. Lift out Old Agitator5. Put in NEW Agitator6. Replace 7/16 Bolt7. Replace Seal Cap8. Replace Top Cap.9. Sit back and enjoy your clean clothes
Washer; I watched the repair video, and replaced the agitator. It was so simple I think that it took longer to watch the video. Refrigerator; I replaced the ice maker, and the solenoid valve. It was very easy to replace the parts, however it took a while to diagnose the problem. I found an appliance repair man that told me what contact points on the front of the ice maker would trigger the clock (so I didn't have to wait for an hour for the clock to activate). There is also a set of contacts that when jumpered will trigger the solenoid valve. It only took a total of 25 minutes to fix both the washer, and the dryer. If you take a piece of 14 Ga. solid wire about 6" long and strip the ends about 3/8" and bend it into a U you have a jumper. If you jump the contact points on the front of the icemaker letters T & H this will start the clock operation. If you jump letters L & V, the solenoid should open to allow water to flow to the tray. If water does not flow, the filter should be checked in the valve. If the valve sounds like it is opening, sometimes the inlet to the ice maker can freeze stoping the flow. In my case I found the solenoid valve was getting only a week signal, and would only function about 25% of the time.
I bought the cog kit. Nice directions on how to assemble but their were no instruction on how to disassemble the agitator. I wound up replacing the whole agitator for $60 vs $6 for the parts I needed. The agitator had only one nut (which you had to take off to get at the cog assembly anyway. The agitator is the way to go. The cogs are halfway down the top part of agitator with no way the get them out without a special tool or ruining the bottom part of the agitator as the clips are part of the bottom piece. If you need special tools they should be listed. If you need to be a trained technician that should also be stated. To give you parts in the middle of an assembly with no instruction on how to put them in the assembly is plain wrong.
Hi I took off the old one and put on the new one quick and easy
My husband just took the bolt in the middle took the broken one, put the new one, put the bolt back the lid the rubber seal and done. Working like new.Basically we did what everyone else did with this part, it help me realize I did not need to call a repairman for this, I knew hubby would be able to do this.
1. Removed the fabric softener dispenser2. Removed Barrier Seal Cover3. Removed bolt and seal4. Removed and replaced CAM Agitator Assembly5. Reversed the removal steps.
First removed the cap, took out the screw, pulled out old agitator and replaced it with the new one
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.