Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11741866
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
Followed video and included instructions and had no problems, went very well.
Help other customers find the most helpful instructions.
Were these instructions helpful?
removed the old parts and replaced with new ones it was simple parts were a perfect fit
I removed the center bolt that holds it in place.Removed the old agitating unit and installed the new parts. Very simple.I was more then happy with the ordering and repairing.I will deffinetly use this system again
With the repair kit and socket.
Repairs went well.....it took less than 10 mins...just followed picture diagram....and test....and it worked well>>>.
simply remove the cap, reach in and pull out the cover,use a 7/16 socket with a long extension,undo the bolt, remove the agitator,turn it upside down and the piece with the 3 dawgs in it will fall out, just replace them with the new dawgs, slide the retaining cover back on untill it snaps into place, then drop it back into the agitator and reverse the removal process and your done, real easy! This is the second time within 10 years I had to replace them, They are only plastic and wear out within 5 or 6 years!
Followed the instructions in the video and everything was easy to remove and replaced the parts and reassembled the agitator. The washing machine is working great.
Bought the agitatop repair kit and bolt, followed the instuctions as well as the video, piece of cake took 15 mins
The fabric softener dispenser pulled right off, then I tugged out the plastic cam cover (which was obviously not as waterproof as intended). The bolt was very rusty. I had to use the socket on the end of the screwdrive handle attachment for lack of a full one foot long 1/4 inch drive extender. Then i had to turn that with an adjustable wrench for leverage. It slipped a couple times but then came off. To disassemble the two halves of the agitator i had to pry on the rather squished tabs holding them together and yank quite hard until it popped off. Then it came apart easily, the cam went back in easily, especially with the provided instructions, and then it all popped back together after a well needed cleaning. The new bolt went right in the cover back on. After a empty load of water to rinse away any remnants it works like a charm.
i watched the video on replacing the agitator and it was very easy to get the job done. Didn't have to search for the right tool, everything was explained in full. Made the job easy. Washer is running nicely.
Your video told me all the tools required and what steps I needed to do. Directions were fool proof, except the required Agitator Grease (your part # PS347804) described in the video is not part of the agitator rebuild kit. Bad planning. Maybe a waterproof grease from the hardware store would work...anyway I took the time to reorder the grease before starting repair. The repair kit did include a new rubber washer for the agitator bolt (I had ordered a whole new bolt). Caution: it would be easy to over tighten the agitator bolt. Make mental note of taughtness, during dissemble. Aside from that I was totally finished with the repair in 30 minutes. And the best was: what a difference in agitator perforance! A twenty-plus year old machine like new again.
Replaced them with the agitator cam kit. It was easy. Hard to get the upper agitator half off of the lower but that was what the husband is for LOL. With his muscle and your "how to videos", it was a snap. If something else breaks this is the first place Im going to to see if I can repair it. This repair cost a whopping $24 and I actually could have gotten away a lot cheaper but bought an extra washer and bolt which I probably didnt need but replaced anyway. I thought we were going to have to get a new washing machine. No way. Machine is working as good as ever. Thank you, thank you XXXOOO
I took the agitator apart and noticed there were little cogs were not contacting the grooves in the compartment. I could spin it by hand in both directions. So I went online to Partselect to see if there were parts available. I didn't have the madel number but the parts list that was at the website made itr easy to locate and purchase. The part arrived 2 days later and the washer was washing clothes within a half hour.
There was a video on the web providing instruction. The longest part of this repair was cleaning the old agitator of soap and fabric softener scum. Once that part complete, installation went smoothly. Didn't realize that the thrust spacer and o-ring for the internal cap came with the kit as it wasn't listed on the kit part list, so I purchased those separately. Not a big deal as it was only a couple of dollars and not enough to worry about. Part Select does an excellent job in making sure you have the right parts and break out drawings to show exactly what's needed to complete the repair. This is the third or fourth experience with them and the accuracy and quick response more than met my needs.
Disassembly and replacement of cogs with new agitator bolt and rubber washer!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.