Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11741794
This tub to housing gasket is five inches long. It is all white in color and is made of plastic. This gasket is intended to fit between the washer tub and machine housing of washing machines.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I had to remove the back lower panel with a nut driver (approximately 8 screws) as well as the front panel which is removed by poping the top of the unit removing 2 screws and swinging the panel down and lifting off. Remove the bleach fill cap (pry off). You'll need a long extension on your ratchet to remove the bolt holding on the agitator. Next remove the inner tub which is held on by 4 bolts. The outer tub is a bit more difficult. You will need to remove all 4 shoulder screws from the top as well as the six that anchor it to the spring assembly around the bottom skirt. Since it was 7 years old I had to muscle the outer tub and rotate it to get around the inner tub transmission flange. I'm not sure which of the 3 parts were leaking so I ordered and replaced all 3.I don't know if it was necessary but I scraped and cleaned the aluminum flange plates where the gaskets seated.At this point it was easy to replace the tub to housing gasket and tub/housing seal. During reassembly I also replaced the basket to centerpost gasket. I went with standard delivery but got the parts the next day.
Help other customers find the most helpful instructions.
Were these instructions helpful?
These gaskets and seals were relatively easy to get to. I replaced all 3. Put machine back together, but washer still leaked. I ended up having to remove more components down along the center shaft towards the transmission. I found that the "tub seal" was worn out. I also replaced the "seal nut assembly" and "O-ring" while I was at it. The seal nut and tub seal were more difficult to remove without the proper tool, but a bigger rubber mallet and strategically placed pliers were enough to break them loose. Once all parts showed up the washer went back together easily and it is now leak-free.
First I removed 2 screws at bottom of front panel and removed it. 2 screws under front of top to lift it out of the way.Then removed agitator following directions supplied in seal kit, removed inner tub, removed transmission shaft nut, then the hub. Cleaned up all the parts as instructed, followed detailed instructions for installing new seal kit. I moved on to belt replacement.I removed the 2 front tub support springs, 4 bolts from motor mounts, disconnected motor wiring at motor and removed motor, then removed 3 screws from pump assy. at bottom of motor and removed it. Replaced worn belt,and reassembled pump to motor,careful to position belt properly between pump mounts.Then reinstalled motor, reinstalled tub springs, hooked it up,ran it to check for leaks, then closed it up. RUNS LIKE NEW
first we looked at schematics on your web site to see what we thought was wrong and if we felt we could do ourselves. It appeared to be seals and gaskets, so we went for it and carefully took the washer apart. We ordered the parts, cleaned the parts we had such as the tub, and were all ready to put back together when the parts arrived. Again, using your pictures, we reasselbled and when we tested, it worked better than it had been in a long time. And we saved a large repair bill!
removed tub and installed all new seals presto no leaks works great
Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.Tipped the machine up to replace the belt.The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.