Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11741780
The lid hinge on your washer is connected to the lid and allows it to open and close. If you find you cannot open or close the lid to your washing machine properly, you may need to replace the lid hinge. This lid hinge is an inch and a half long, all white in color, and it is made entirely of plastic. To complete this repair, you will need a Phillips screwdriver and a putty knife to remove the top of the washer, in order to access the screws that hold the lid hinge in place. Be sure to disconnect the power to the washing machine before beginning this repair.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I had to pop the top of the washer which is hinged in back. Raised it up and removed old hinges. replaced "hinges and hinge pins. It works like new.Thanks for your "website". It was very easy finding the parts I needed.SincerelyBill Hines
Help other customers find the most helpful instructions.
Were these instructions helpful?
I popped the clips on both sides of the top with the putty knife. Raised the lid. Unscrewed the one screw on the old hinge. Screwed on the new.It took a PhD in hinge replacement to do this.
Easy to remove broken part. Found rust, so after cleaning I applied paint (I let dry overnight). By manipulating the washer drum, moving left and right, the screws were easy to get to. However, to get the screws back in took tightening by strong hands. Plus, found that the lid sensor had worn out, so that was adjusted.New screws would probably make the job easier.All is fantastic and I found it was "easy" to replace with finishing help from strong hands.
Remove two screws holding a special clip on the back of the washing machine (near top- one on each side). Top of washing machine pops off now by prying front edge up (2 snap type clips hold front edge of top down). Once top is loose just pivot it up on edge so you can get to the bottom side of it (don't have to remove the wires etc. as they are long enough for this). Remove one screw in each hinge half located on bottom side of washing machine top and remove old hinge half from top. Remove broken hinge halves from door to washing machine by removing one screw from each one. Put new hinge halves together and fasten to door. Then set entire hinge/door assembly on washing machine top and screw to top as an assembly. Snap top of washing machine back down on front of machine and put clips/screws back in on back of machine.
Not knowing what I was doing, I just started taking the machine apart. Finally, turned the machine on it side and found the belt barely holding together and I was not able to move it. When I removed the belt I discovered that the discharge pump was stuck. Therefore, I also removed it. Everything else seemed to work. When I order the new pump along with a belt, I was glad to see the description of the pump included the pulley. When the parts came they where exactly what I needed and I was able to install them quickly and but the machine back together with out have any extra parts left over.
I had my son remove all of the old hardware with an allen-key wrench. He then proceeded to install the new hardware. Fisrt he installed the pins on the lid. Next, he installed the hinges to the washer, leaving each hinge loose. Finally adjusting the lid until the screws for the hinges were completely tightened.
push the washer tub as far as you can and use a long screwdriver to take hinge off,do the same for other side. Lid will then be removed for access to hinge pin,remove hinge pin and reverse process. Very easy repair. Very fast delivery from PartSelect.
1. Open washer lid.2. Remove right hinge mounting screw by leaning agitator/tub assembly to the right.Do the opposite for the left hinge mounting screw.3. Remove and replace both hinge pins on the lid. 4. Install both hinges on the pins and install lid back on the washer.
Just popped open the top of the washer, took the broken hinge off and replaced it.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.