Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11741733
This burner cap assembly is sold with the spark electrode. Please note this part has been redesigned and no longer requires a gasket. Sold individually.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Replacement of these burners is very easy. You just twist the burner counterclockwise a quarter turn and pull it out. (You may need a big wrench if the range is very old.) Once out, just pull the two wires off and push them onto the new burner. Crimp them on with pliers if they're loose -- mine were. Twist the burner back on.If the gasket under the burner has disintegrated, don't worry about it. They don't offer replacements for them because they're not necessary as a safety feature. They were designed to keep overspills from running under the cooktop, but the ridge around the hole is likely higher than you'd ever need.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Burner head arrived when I got home from work. Just timely to cook for dinner that monday night, got the 4 burners disconnect the element from the old burner, then connect element to the new bunners, in less than 10 mins, and I had save estimate $600 buying a brand new stove or gas range, this will last me another5 to 10 years. Especially this time of recession
The burner rusted after years of spaghetti pots boiling over. When I went to twist the the burner to remove it the top portion broke off. This left the bottom side of the burner stuck into the cook-top. I put some 3-in-1 oil on the rusted rim for a day or two. I had to drill the phillips head screw and twist it with a vise grip. I used a pair of pliers to grab the center of the broken-off burner part. After a few tries it broke loose and was out. The rest was easy. I recommend sealing the rim between the burner and the cook-top. I used silicone sealant. This should keep the water from leaking underneath the burner and into the cook-top.
A quarter turn counter-clockewise and the burner came out. Disconnect the old wires and connect the new wires. Place the burner in its place and a quarter turn clockwise and it was set.
Unscrewed burners (1/4 turn and pop out) then removed set screws, opened top of range. Used 1/2" wrench to remove gas pressure fittings, popped new ones in, replaced wires. Placed top down and then put screws in to minimze movement of tubes.
Disconnected the burner cap, unscrewed the drip bowl screws (2), removed the drip bowls, installed the new bowls and reconnected the burner cap. I intended to replace all four drip bowls but two of them came with large chips on the edges. I plan to purchase two replacements soon.
The burners turn and lift. I replaced two. One turned very easily, the other was stuck so I used liquid wrench and plumbers pliers. I did get it off. Once off, the old wires slipped right off and onto the new burners. Those twisted on very easily. Good as new easy breezy.
Removed the old burners with a Plumbing Pipe Wrench by turning 1/4 turn counter clockwise. Disconnected (2) wires and replaced with new Sealed Burners. The simmer burner wires were slightly diffrent from the original but they do fit by opening the connector with screwdriver and then clamping once wire inserted.
The repair was a no brainer - twist to release the old burner - disconnect the spark wires. connect the spark wires on the new unit - drop it in and twist to lock - about 2 minute job
I used a pipe wrench to turn the old burner off and removed the crumbling washer underneath- no need to replace this. I took off the 2 wires, crimped them onto the new burner, twisted it back into place and presto- all fixed!
I have a maytag stove and the burner was coroted and it had to be replaced. I went seaching in the Internet for a new stove automatically then I thought maybe I can buy the part so I found this awesome website partselect.com. I was intrigue to see if I can find this part I needed so I put in the model number in an seached and then I placed the order not only for the burner but for the grates as well the website is designed very well! Easy to navigate to find the items your looking for. When I recieved the parts in the mail it took me less than 6 minutes to attach the burner and place the grates on the stove it was a great experience all the way around. I would recommed this web site to anyone.
Unscrew the burners an install new ones! Anyone could do this.
I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .
My husband simply twisted out the old burner with a pliers and attach the new burner. Simple and easy....
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.