Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11741460
This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins is no longer present. Terminal size is 3/16".
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Well - I'd taken my clothes out of the dryer and put them on the pool table and went upstairs to go to bed. I thought at last moment to go pee first and ran back down stairs. Downstairs I smelled the odor of burning lint. When I looked into the laundry room, my dryer was glowing red hot - Sweet! It seems that the heating element was staying on even though the dryer was off. I looked in the various descriptions of myriad failures of dryers and didn't find that one in the documentation at all. So - I replaced the thermal fuse, the Thermal cut-off and the timer. Alas - the replacement timer had to be replaced because the clock motor was defective. When the second replacement timer arrived, it was quickly installed. Long story short - if the timer is in any play mode, the heating element stay on full blast - not low, not medium, but full on chub - and this is whether the fan or tumbler are on or not, door open or not. And so the mystery anomaly remains un-repaired, unresolved and perhaps even, undiagnosed. Note - the new Thermal Cut Off does not cut off anything even when it cookin red hot. Strange.
Help other customers find the most helpful instructions.
Were these instructions helpful?
My wife was doing a load of laundry when she thought the the dry cycle was finished she found the cloths still wet. When she went to restart the dryer nothing. I did some research online and found the most common problem was the thermal fuse. I removed the back of the dryer removed the fuse and checked for continuity with my volt meter. I thought that I was going to find alot of lint build up. However I did not so I decieded to also replace the thermostat, using the thermo cut-off kit because this might have caused the fuse to fail. I ordered the parts from partselect and they arrived in two days. Partselect has excellent instructional videos on how to make the repair. It was quick and easy and saved the money of just going out and buying a new appliance.
Everything seems to work on the electric/gas dryer, but would not generate any heat. Did some research and ordered the thermal fuse & thermostat based on that. Replacement was simple and went well, however it did not fix the issue. Should have checked the continuity first as I found the "replaced parts" to be good. Have checked all other possible symptoms except the heating element, which requires addition labor. Overall, partselect portion was as advertised. All parts arrived quickly and were priced fair.
The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about two days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.
checked to see what the problem might be according to your website, ordered the recommended parts, received parts within 3 business days, watched video on website with instructions, replaced parts and surprise, dryer works as if nothing ever happened. thank you for the straightforward, no nonsense information and video provided in your website and the promt efficient service
after reading your site reviews I bought all 3 thermostat's. It took about 30 minutes (with a coffee break) to change them all out and that saved me $400.00. I popped the lower front pannel off and all three thermostat's were accessable from there. i needed to remove the lent trap and tube which is held on by 2 screws to access the thermal fuse and cycling thermostat. there was a lot of lint trapped in the tube. it was a few screws and some spade connectors. very easy repair. as I said above buy all 3 and it saved me $400.00.
First time ever repaired anything let alone a dryer, I watch the video and followed instructions, was pretty simple, Works like a charm
I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hoses. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.
removed the back of the appliance disconnected the vent pipe. Found the problem was a flying squirrel had committed suicide in the vent pipe and as a result had blown the thermal fuse. Tested the fuse to see it was blown with a multi-meter. Ordered the fuse from PartSelect online. fair price shipping was quick. Received the new fuse in 4 days and had the dryer working again in about 10 minutes.
I unplugged the appliance and turned off the gas supply. I removed the exhaust hose by loosening the clamp with a nutdriver. I removed the back panel screws with a nutdriver and removed the panel. I pulled the wire connectors off of the thermostat and thermal fuse. I removed both parts using a screwdriver. The thermostat terminals were slightly different, but the new style terminal ends came with the thermostat. I cut the old style terminal ends off of the old wiring with wire cutters. I stripped the wires and crimped new ends on the wires. I replaced the parts and wiring in the reverse order of removal. I replaced the back panel and exhaust hose. I turned on the gas supply and plugged in the dryer. I turned the dryer on to test it. It worked well. No problem!
Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man. Heater thing was part # 3387134and the fuse was 3392519
Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!
The repair descripition was accurate. The difficult part was getting the old switch out. It has a release clip that is hard to reach. It took several tries and a bit of force to get the old part to release from the cabinet.In stalling the new part was easer that the instructions explaned. There was no need to split the original plug. I unplugged the old switch, plugged in the new and snapped it into place. 30 seconds after I started the reinstall it was in the cabinet and working
My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 business days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!
Prior to ordering parts i moved the dryer out and took the back off the dryer with a nutdriver. I noticed right a way the heating element was damaged and burnt up. I ordered the above parts and recieved them in two to three days. the parts on my dryer were easy to get to and I just matched up the parts i recieved and replaced them one at a time. It only took a nit driver to remove them and plug the wires back in to the new parts. the dryer works like new again.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.