Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11741444
This part attaches to the exhaust duct of your clothes dryer.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
un pluged it then removed the hose took the back off took out the 2 screws out of each part replace it with the new parts , then pluged it back to make sure it would work and it did the very first time. i'm 1 happy roper owner.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Removed the back of the dryer taking off the screws. Found the disposable thermal fuse. Unplugged the 2 blue wires connected to it. Removed the screws holding the part in. Replaced the old part. Reattached the blue wires. Put the back on the dryer. And voila! That simple!I'm a 39 year old woman with absolutely no patience for tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
I checked parts select.com and followed the guide lines,ordered the correct parts thanks to the web site help.parts arrived in 2 days,A very easy install and back to work drying clothes.Thanks parts select.
After unplugging the dryer, I removed the bottom panel in front. Remove the the filter inside the dryer and remove the filter housing below. There you can see the thermal fuse on the air duct, its white with two blue wires. You can check it with a ohmmeter after removing the wires. If its open its bad. Its held in place with two sheet metal screws. After replacing the thermal fuse the dryer worked fine. However I would suggest cleaning the air duct and the outside discharge opening. Hope this helps.
Did an Ohm test on the old Thermal Fuse found it to be bad. Replaced it with a new and the dryer is back to working great. Your suggestions saved approximatley $150.Thanks for the help.
We took the screws off of the back, took out the thermal fuse and replaced it with the new one.We watched a video of how to do it which made it so easy.Works great!
Checked online for symptoms.Pulled panel from front of unit (no tools required)Vacuumed all lint from unit to see if that was a problem.Removed the exhaust port which comes off with 3 hex head screws. Based on the symptoms, I pulled the wires off the thermal fuse and did a continuity check on it. There was no continuity, so I knew I needed that part. Since a common reason for that to fail is the cycling thermostat allows the dryer to get too hot, I replaced that thermostat as well, just to be safe. Due to closeness to the drum, I had to use a socket to remove the hex head screws on the two electronic parts.Total time was about 40 mins. to diagnose and 20 mins. to replace the parts and verify correct operation.
Used an inexpensive multi-meter to detect that there was no continuity through thermal cut-off (high end) or disposable thermal fuse. I identified these parts by reading your online schematic of the dryer. I noted that the flexible ducting had been crushed on the dryer which lead to the feasibility that the thermal cut offs, especially the thermal fuse could have burnt out. Ordered the parts on Monday, drying clothes again on Wednesday.
With the help of YouTube, I was able to watch videos of how to disassemble and reassemble the dryer. I watched a video showing where the Thermal fuse and Thermostat was located as well as how to test them with a meter. I watched another video showing how to replace the drum belt, showing step by step instructions. Without YouTube it would have been a whole different story!
Unpluged dryer power cord.Removed lower front panel (two snap clips at top of panel)(Rear panel cannot be removed from this dryer). Removed blower/filter housing (held by two screws). Found blown fuse by using an ohm meter across the fuse terminals with one wire removed - no continuity. When new parts arrived, I removed two wires from fuse and four wires from thermostat. Removed two screws holding fuse and two screws holding thermostat, and removed both parts. I then reversed the above procedures.Dryer works great!Total cost, including shipping, was $47.76
i followed your instuctions for the gas dryer with the ohm meter which i had, and found the part that had 0 ohms. but i did clean all the lint out first that took more time. i was glad you had the diagram to show the parts and numbers. thank you, rich
Unplugged power cord. Removed rear panel screws and panel . Removed the two wires connected to part. Removed two screws holding part and replaced all components in reverse order.
I ordered the wrong part. It was pick and choose from the info provided.I checked again and found one that's 58% of the time the part.
This was so easy to take apart and put back together following the repair video. I figure my family saved $200.00 by doing it myself.
All parts were correct is what I should say to begin. Replacing the parts was a bit difficult, but I got the job done. My Kenmore dryer has been serving our needs faithfully for 14 plus years, and hopefully with these new parts, it will last a bit longer, thanks to your service parts. Much appreciated, and keep up the good work!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.