Quick Question!

Have you ever purchased from PartSelect.com before?

11741341-1-S-Whirlpool-WP3378134-Cap, Wet Agent Assembly
11741341-1-S-Whirlpool-WP3378134-Cap, Wet Agent Assembly 11741341-2-S-Whirlpool-WP3378134-Cap, Wet Agent Assembly http://www.partselect.com/Schematics/Maytag/QOP7DTSW.gif

Cap, Wet Agent Assembly

PartSelect Number PS11741341

This cap does not require the use of a o-ring seal.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not dispense detergent.
  • Not cleaning dishes properly.
  • Leaking.

Compare At

$9.12

You Save

$1.52

Your Price

$7.60
Order within the next 12 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 5 reviews What's this?
1-5 of 5
 

16 of 27 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Louis from Niceville, FL

Water dripped out from the bottom of door.

Diagnosing the problem, i.e. finding the source of the leak, was the hardest part. The best clue was the leak only occurred well into the cycle when the water was hot and steam was coming out the vent. I then assumed there was a bad seal and steam & condensed water was leaking down into the door. I replaced the vent duct & seal, a broken drip cover (an internal part in the door), and replaced a missing rinse aid cap. This stopped the leak.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
  • Cap, Wet Agent Assembly
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Debra from York, PA

Cap did not stay in the hole any longer.....was melted

Just screwed the new cap in. This PartSelect was AWESOME. So easy. Lighting fast shipping !!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Nicholas from Pleasanton, CA

Replaced broken/worn parts

Simple replacement

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Melissa from The Colony, TX

Wash arm retainer nut snapped in half

First I pulled the top half of the broken retainer nut out of the lower wash arm assembly. Then I took the was arm assembly off, removed the other half of the screw, set the lower spray arm seal into the lower wash arm assembly and screwed the wash arm retainer nut back in. As a bonus, I decided to replace the broken Wet agent cap. Had to use needle nose pliers to unscrew the broken bottom stuck in the well... That was the toughest part and it wasn't critical to the dishwasher functioning.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 22 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Jim from Oktaha, OK

Soap lid missing

Replacing the pin with the spring is a little tricky, it was hard to hold it. And the little plastic pin breaks real easy too, its hard to get the lid to snap in place without breaking the pin.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5