Make sure you haven't got the discount earlier.
Disk & Mount Assembly WP3369012
Fits your RUD3000HQ1!
Rated by 5 customers
Easy
1- 2 hours
Ratings submitted by customers like you who bought this part.
Fits your RUD3000HQ1!
PartSelect Number PS11741267
Manufacturer Part Number WP3369012
Manufactured by
Whirlpool
Product Description
Disk & Mount Assembly Specifications
Used in the dishwasher pump area.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Dishwasher.
This part works with the following products:
Whirlpool, Roper, Kenmore, Estate.
Part# WP3369012 replaces these:
3369012
Customer Repair Stories
Average Repair Rating: 2.5 / 5.0, 5 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Leak from the impeller
Replaced the impeller using the kit. Had to brake the impeller since it was stocked due to rust.
Other Parts Used:
-
Julio from ORLANDO, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench (Adjustable)
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump impeller went crooked, apparently both from wear and moving the unit. Would not then stay in place.
Disconnected hoses (2) from pump housing. Disconnected pump housing from motor (3 allen screws, not too acessible). Unscrew spray arm from pump housing (this is done by hand; no tools as the "nut" is about 3" diameter and made of plastic) Open up the pump casing and replace impeller and the bearings on each side. The thing that takes some
... Read more
time is to mop the water that comes off at almost each step. There is probably an intelligent way to drain everything first. I did not order the large seal (kind of a large rubber donut, larger than a donut) between the arm and the pump and I shoiuld have as it was difficult to keep the old one from not leaking: Since by hand you cannot tighten the large nut very hard and tools could damage or break it. Applying upward pressure on the pump while tightening did it. (The pump and motor are all mounted on flexible mounts, like the heavy hoses connecting to the pump housing, so that there are no vibration.)
Read less
Other Parts Used:
-
Guy from Santa Fe, NM
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
slow leak at motor/pump interface
Got parts breakdown online, took pump assy apart, ordered new parts, replaced bad parts, put pump assy and dishwasher back together, piece of cake, no problems.
Other Parts Used:
-
Donald from Webster Groves, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump not working properly
I removed the inner nut holding the spray arm onto the pump. Turned the washer on it's back and removed the wire clip holding rear of the pump motor. Completely removed the pump housingand motor from the washer. Removed three(3) long screws holding the motor to the pump housing. Removed the dish from the housing and removed the old impel
... Read more
ler and seals .
Cleaned the pump housing of calcium with lime-a-way. Reinstalled all new parts in reverse order as they order taken off. Cleaned inside of dishwasher with lime-a-away and general purpose cleaner. Reinstall pump housing and motor on washer in reverse order as they were taking off.
Reinstalled washer into cabinet and connected all hoses, drain lines and electrical wired. Turned washer on and watched it run throught a complete cycle. Worked just fine and no leaks. Parts were great.
Sincerely,
James
Cleaned the pump housing of calcium with lime-a-way. Reinstalled all new parts in reverse order as they order taken off. Cleaned inside of dishwasher with lime-a-away and general purpose cleaner. Reinstall pump housing and motor on washer in reverse order as they were taking off.
Reinstalled washer into cabinet and connected all hoses, drain lines and electrical wired. Turned washer on and watched it run throught a complete cycle. Worked just fine and no leaks. Parts were great.
Sincerely,
James
Read less
Other Parts Used:
-
James from Little River, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leak at the seal
Getting the dishwasher out was easy. Getting to the impeller was easy. Getting the impeller off of the motor shaft was the difficult part. I had to use my Dremel tool with lots of cutoff wheels to cut the impeller off of the motor shaft a little piece at a time. It appeared to be rust on the motor shaft that was causing the impeller to no
... Read more
t come off. There is not much room for the Dremel so be careful not to nick the pump housing or cut into the motor shaft. Keep the vacuum close by to clean out the plastic impeller shavings. Clean the rust off the shaft with steel wool, fine sandpaper etc. Assembly was easy once everything was cleaned up.
Read less
Other Parts Used:
-
Craig from Southern Pines, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11741267
Manufacturer Part Number: WP3369012
Manufacturer Part Number: WP3369012
Brand
Model Number
Description
Back to Top
Disk & Mount Assembly
$
36.46
On Order
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.