Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11741235
This part holds the bleach until it is ready to be released into the cycle.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump.
Help other customers find the most helpful instructions.
Were these instructions helpful?
First I went to this site and read what everyone had to say on leaking pumps. After finding the model number, I looked at the parts list, and found what parts I thought I would need. First I shut off the water and unpluged the washer Replacing the water pump was very easy after reading what other people had done. I pulled the washer out from the wall about 18 inches and tilted back on a 45 degree angle. The pump was now in plain sight and helt in with two slide clamps. Using a pair of plyers I remover both clamps from both hoses on the pump. By pushing to the outside of the pump I was able to remove both of the slide clamps. This allows the pump to be lifted out and off the motor shaft. As my washer had just started leaking " about one week" the pump slid off the shaft easy. There was no rust on shaft. Pump shaft has a slot in it so the pump can only go on one way. By reversing the way I removed the pump I was able to slide the new pump back onto the shaft and slide the slip clamps back over the pump. Replacing both hoses and both clamps. Now pump was in place. I pulled the washer away from the wall and slid back into place. That took care of the pump. For the top side I removed the top part of the agitator by pulling up and removing the part that holds the softner. Under this was a piece of plastic that I was able to lift out. Under that was a 12MM bolt with a rubber washer. Using a scoket set I removed the bolt and washer. Lifting up on the agitator it came right out. Pulling on each end of the agitator I was able to pull it apart. Inside was a large plastic washer and agitator directional cogs all in one piece. This piece just lifts up and off. I replaced the old piece with the new on and slid the two agitator back togeather. Setting the agitator back into the washer and put the 12mm bold and rubber washer back on. Then I put the plastic back on and set the top softer cup back in place. Snapping in the bleach dispenser was very easy, just shap into place. Pluging the washer back in, and turning back on the water I ran the washer with no clothes in it so I could check for leaks and make sure everthing was working. Repairing both parts took about 30 minutes and now the washer is like new.
Removed bolt in center of agitator then slid agitator straight up and out replaced the dogs and the other parts that came with the cam kit i also replaced a few of the other parts that wear in the agitator ,you can actually re-cut the teeth on the dogs with a razor so that they will work again ,but new parts are very reasonably priced and the parts arrived very quickly the next day .
Ordered part and within 2 days it arrived. Removed broken knob and twisted new one on. Awesome job getting the part to me so fast. Thank you!
Remove Agitator cap and inner cap. Unscrew center retaning bolt. Lift out agitator assembly. Remove thrust washer and ratchet assembly. Install ratchet and thrust washer in top of agitator. Set agitator on shaft. Install and tighten center retainer bolt. Install inner and top caps. Load it up, and REALLY wash some clothes.I have been fixing appliances and a many other mechanical things since my early teens.When I went to the CONTRACTOR’S store, they treated me like a young dumb kid that shouldn’t be allowed to buy repair parts, or the part is unavailable. Thanks to the Internet and places like PARTSELECT.COM, I can buy the parts I need and not have to call a shysters repairman to rip me off. PS.com provided me with the parts I wanted without disputing me. They also provide simple, clear, and to the point instructions for replacing the old parts. Even someone doubting their own ability can handle a complicated repair. PS.com not only has the major parts that fail, like motors, but also the little things like switches, knobs, trims, handles, seals, and all the other minor parts.
After 3 years of hard daily use, the small feet that hold the Bleach dispenser in place broke off. The new dispenser was easy to snap into place and now the washer is good as new.
Tipped onto side to access from bottom. Removed motor and replaced drive coupling between motor and gearbox. Do not turn machine completely upside down as gearbox oil will leak out of vent hole in transmission.
Repairs went well.....it took less than 10 mins...just followed picture diagram....and test....and it worked well>>>.
Went online to Parts Select and typed in Model #. Looked thru repair help and found very simular problems. I did disassemble the upper prtion of the aggitator by removing softner dispenser. Once inside I used a shoe string and routed it thru the two handles on the plastic cover and pulled up moderately, exposing the cam and doggs. I used a 7/16" socket on a 6" xtension to reach the mounting bolt. Slowly turn bolt counter-clockwise holding the lower agitator. Once the mounting bolt was out I temporarily replaced the plastic cover. I pulled up on the UPPER agitator to completely remove it from the tub. Once set on a firm surface I again pulled out the plastic cover ,bolt and cam cover, exposing the cam and dogs. I shook them out. I replaced everything with what was included in the agitator repair kit ( great kit). Everything for assembly is as the instructions state and totaly a reverse process. Take care not to over tighten the bolt. I did take this oppurtunity to clean the tub and agitators. I did also remove the lower agitator to clean the area. Thanks Parts Select!
Order Switch Lid, now my machine is working like a new machine, had to remove the lid and pop off the old switch lid bascially from the back. I love partSelect.com if ever another problem, will use PartsSelect.com.~Thank you.
1- Ordered and received a new bleach dispenser.2- Removed broken dispenser from machine.3-Dropped in new dispenser.Viola! It was fixed and no more random left over bleach stains on non-bleach loads of laundry! :-)
Changing the parts was easy.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.