Quick Question!

Have you ever purchased from PartSelect.com before?

http://www.partselect.com/Schematics/Maytag/53128.gif
See part 7 in the diagram
http://www.partselect.com/Schematics/Maytag/53128.gif

Timer Assembly - with chiming mechanism

PartSelect Number PS11741080

This timer assembly is almost five inches long. It comes with a chiming mechanism and runs at 1/3 horse power.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not shut off.
  • No heat or not enough heat.

Compare At

$152.35

You Save

$25.39

Your Price

$126.96
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 7 reviews What's this?
1-7 of 7
 

15 of 18 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Jerry from Las Vegas, NV

Timer assembly would not advance

Removed old timer assembly, put the new one next to it and as I disconnected one wire from the old part, I connected it to the new part, that way I was able to connect each wire to the right place.
It was very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
  • Timer Assembly - with chiming mechanism
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Wrench set
Customer: Richard from Keswick, VA

Dryer timer dial was cracked and thus would not turn the timer pivot.

Ordered the three pieces of the dryer dial and replaced the old dial with the new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
  • Timer Assembly - with chiming mechanism
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Randall from Viper, KY

Dry er would run but no heat.

Appliance dealer stated that usually timers did not go out and thermostats were most likely . Tried all and called repairman that did not show. Removed cover found burned gear in timer ordered. The part is easy to replace just change wires one at a time or take a digital pic of the wires.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Robert from Ray, ND

The dryer would not shut off. The timer would not advance,

I replaced the timer and timer dial skirt which was very easy to repair. The dryer would not shut off and the timer would not advance. I could manually use a plier to move the timer and it would shut off then. I replaced the timer and it works well now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
  • Timer Assembly - with chiming mechanism
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Walter from Flagstaff, AZ

Timer quit working after lighting strike

remove back cover 3 screws, change wires in same order as old timer, remove two mounting screws under timer dial, check voltage-replace temp sending control attached to brown wire.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Timer Assembly - with chiming mechanism
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Dick from Alexandria, VA

Dryer wouldn't shut off.

Had the dubious distindtion of having two switches (start switch & the timer) go bad within 3 months of each other. The start switch has been previously discussed.

The access plate to the controls is secured be 3 phillips head screws and 2 nut-driver bolts.

The switch itself is secured from the front of the machine be two phillips head screws, located underneath the knob which is easily pulled off.

Just replace the wires one-by-one using needle nose pliers on the clips .
A real no-brainer.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Timer Assembly - with chiming mechanism
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Barry from Hollywood, FL

Dryer wouldn't stop automatically

Removed the knob. Removed back panel. Removed the timer (2 screws). Pulled off wires and put them on the exact same spot on new timer. Attached new timer and replaced panel. Dried my cloths to perfection! (While I took a nap)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-7 of 7