Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11741074
This seal can be used for the front or rear drum. Adhesive is NOT included.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I've never even opened this dryer before so I looked at one of the installation videos PartSelect has. I found one using my model, which made it really easy. I removed the front panel and door, then lifted the top of the dryer up on it's hinges: that's a great feature because you need the top out of the way to remove the drum. I took the belt off the drum, lifted it up and pulled it straight out. I did buy a pair of snap ring pliers to remove the snap ring off the drum support shaft. I think you really must have those to remove and replace the rings. Be careful when removing the snap rings. I shot the first one across the room like it was a rubber band. We had a good laugh. I used a wrench to hold the nut on the backside of the roller shaft and unscrewed it. I screwed the new roller shafts on, slipped the drum rollers on them, then carefully used the snap ring pliers to place the rings on the front of the shaft to hold the rollers on. While I had the unit opened up, I figured I should go ahead and replace the multi rib belt. I put the ribbed side on the drum and sat the drum on the rollers . The tricky part is now getting down on the ground, reaching under the drum for the belt. Make sure the belt isn't twisted anywhere on the drum or in your hands while you pull the belt under the idler pulley. Hold the belt ribbed sides together while feeding the belt under the pulley. It takes a good deal of strength to move the pulley over so you can hook the end of the belt on the shaft. Once you've gotten that attached, put your hand inside the drum and rotate it a few times to make sure you connected it properly and that you placed the belt in the right spot on the drum. It was easy to see the black stripe around the drum where I'd taken off the old one.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Turned off gas and unplugged dryer1) Removed bottom front panel2) lifted top panel up like a car hood3) Removed door springs4) disconnected electrial connections to door unit, removed door unit5) removed drum, scraped old felt from drum6) glued new felt with a very strong glue (nanoglue or gorilla glue, same thing), let it dry overnight7) secured back inside panel, replaced drum and put dryer back together.
The dryer disassembly was pretty straightforward. The drive belt slips over the drum and easily prys over the drive and idler pulleys. The drum seal is held in place with the existing metal tabs. The old drum glides had to be drilled out and the new ones pop rivited in easily. Overall a rather simple process and the dryer sounds and drys like new again for minimal expenditure and time. Probably would have cost $200+ had I had a service person do the work.
1 - unscrewed door2 - made a mess because the directions did not work for my dryer3 - figured it out = eventually4 - popped loose the front panel5 - unscrewed metal bars (that were holding the top down in the front)6 - lift front like a hood on a car7 - unscrew the rest of the front until the drum was loose and I could get to the felt strip8 - glue new strip on where the old strip was = to the front and back plates that hold the drum 9 - put it back together :)
If you are cursed with owning a Maytag product then you'll be glad PartSelet.com is in business. I get all my parts here.My dryer motor burnt a phase. The tear down was very straight forward since there isn't much to a dryer. I did the tear down in the driveway. The dryer was full of lint so I blasted it with compressed air to clean it up. Keep all your parts in labeled baggies as you do the tear down. Reassembly goes much faster. The hardest part about changing the motor was getting the motor clips off. They are tough buggers. I used slip-joint pliers & finally popped them off. This job is simply enough for the average monkey. Just use the diagrams on partselect.com if you forget where something goes.I shipped everything via fedex 2-day. It took 5 days to get here. partselect shipped it fast. fedex was the problem. I guess the boys at fedex have a public education is they think 5=2.
1. Remove 2 screws that hold door hinges on. 2. Remove 2 screws on opposite side of door hinge and remove 2 plastic clips.3. There are 2 hex screws that hold the front panel on. Remove these and the panel is held on by a flex clip. Gently twist the top towards the outside of the dryer and they will come free.4. tilt panel forward and lift of 2 clips at the bottom.5. Remove the screws under the cover panel which will release the drum holder and lint collector. 6. Lift top of dryer and lift out drum.TAKE THE TIME SINCE THE UNIT IS OPEN TO VACUUM OUT THE ENTIRE DRYER. CLEAN OUT THE EXAUST TO IMPROVE EFFICIENCY AND SAFETY.7. I replaced the rear felt by using a flat head screwdriver to lift tabs and install felt. Using the screwdrive I compressed the tabs to hold the felt.8. The baffle was installed inside the drum and using 2 hex bolts to hold the baffle in. I added 2 washers since the hole was inlarged due to the baffle becoming loose and pulling through the metal drum.9. Re-install the drum and push rear felt to the outside of the drum.10. The front drum needs to be installed. Push the felt to the outside of the drum and check the rear felt to ensure it is still on the outsid of the drum. Install 4 hex screws to secure front drum holder. 11. Insatall lint catch unit with 4 additional hex screws.12. Verify the lint collection panel lins up with the exhaust fan at the base. When units line up tighten all 8 hex screws.13. Reinstall front cover panel by inserting panel on bottom clips and tilt up to the dryer. The top corners are gently twisted to the outside of the dryer to reattach to the spring clips. Use 2 hex screws to attach panel.14. Re-attach plastic clips and 2 screws on side opposite of door hinges.15. Re-attach door hinges with 2 screws. Cleck to ensure the door closes.16. Check dryer operation.
Follow instructions on this website and be sure to pull the felt seal fairly tight as you work your way around or you'll be a little short at the end...
Replaced tensioner pulley along with felts, rollers, shafts, belt, and bearing pads. This dryer is 21 years old and has been serviced by myself at 15 years old. I replaced everything mentioned above except the tensioner pulley. This is a great running dryer but always remember to change the tensioner pulley when the unit is apart. Also have a third hand when mounting the belt and drum. Very easy other wise.
Opening the cabinet allowed for a through examination and listing of the worn components: 1 defective idler and mounting shaft, 1 worn drive belt, 2 sagging felt seals, 1 worn glide surface, 1 dead light bulb. Replacement parts arrived in two days. After a through vacuuming, reassembly was a snap. Both roller/shafts and glide pads were replaced as matched pairs. Unit operates now as factory new. I am not a trained repair person but simple logic, sufficient care, and attention to a clean assembly routine is all it took.
i removed the front cover .then i removed the two screws thet held the top and then raised it up then silde out the drum. replaced the rollersthat the drum runs on. then just put it back together. not a hard job at all.
I removed the screws from the back, ( top ) then i removed the door, then the front cover.. then the blower shroud, then the front tumbler. and the drum after that it was easy, This was easy to work on.
I watched all of the video provided for repairing each of the parts and used them several times! They were excellent and beneficial! I used the suggestions provided and found the involved correction to do exactly as planned. The end result was very good and the dryer now works like it is supposed to without any noises. I thank you for all of your help.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.