Quick Question!

Have you ever purchased from PartSelect.com before?

11740805-1-S-Whirlpool-WP315843W-Left Side Back Guard End Cap
11740805-1-S-Whirlpool-WP315843W-Left Side Back Guard End Cap 11740805-2-S-Whirlpool-WP315843W-Left Side Back Guard End Cap http://www.partselect.com/Schematics/Maytag/27384.gif

Left Side Back Guard End Cap

PartSelect Number PS11740805

This right side back guard end cap is used for many ranges. It is all white in color and it is made entirely of plastic.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

Compare At

$37.61

You Save

$6.27

Your Price

$31.34
Order within the next 5 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 4 reviews What's this?
1-4 of 4
 

11 of 12 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Richard from Bealeton, VA

Broiler stopped workin in summer. Oven had no heat for wife to make christmas cookies.

First thing I tripped the range breaker. Pulled the range out from the wall and unpluged main plug. I then removed the 12 sheet metal screws from the back lower cover.
I then unpluged the wires from the four element connections and marked the color on the range back.Two upper blue and red and two lower yellow and red. I then tested the resistance of the elements to confirm that they were bad. With volt/ ohm meter set for OHM'S I had no reading.
When my new parts arrived I first made sure that they matched the origonals. I tested the OHM'S on the new parts and began the change.
I removed the two upper element holding screws on the inside rear wall. I then removed the two hanging support screws from the inside top of the oven. For the oven element, simply remove the one screw at the back wall.
Reassembly is reverse of removal.
The element ends will stick out the back side of the range about one inch.Be sure that insulation is in place and that there is no contact between element ends and metal walls.Attatch the wires as you had them marked on the back. Replace the rear cover and tighten all the screws. Plug main plug back into socket. Reset breaker and slowley turn oven control up to a low temperature setting.After a few minuets the oven indicator light will go out.Open oven and check the temperature.
End cap has three screws to remove. Slip off old cap and replace with new one. Snug the three screws. Push the range back in place.
Have the wife back some cookies and enjoy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Left Side Back Guard End Cap
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Richard from Lincoln, RI

End cap deformed from heat

Removed 3 screws, lifted the top control panel. Adapted new plastic end panel and replaced new end cap an refastened with original screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: David from Hinckley, OH

Broken parts

Simple repair procedure: pried out broken switch and pulled wires off then reversed this procedure, removed screws from broken end caps and replaced same. Parts were easy to order as there was an exploded view. This made picking out the parts required. There is two switches on the front of the stove and with out part numbers or a service manual the exploded views made this choice easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: James from Des Moines, IA

Old caps were cracked, and discolered

1. removed the screws that held the caps.
2. Moved the stove away from the wall.
3. Unplugged the power cord, for safety.
4. Removed the caps.
5. Install the new caps.
6. Plug the power cord in.
7. Place stove back in positon against the wall.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-4 of 4