Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11740723
This part lights the gas burner to create heat.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Lift the top. Remove (2) screws holding the front of the dryer in place. Lift the front off the 2 retaining clips on the bottom of the dryer. The hardest part of the install was removing and replacing the igniter. A couple of helping hands from the girlfriend to hold the parts in place while I replaced the two screws was very helpfull. Installing the multi rib belt was also very easy with the help of a second pair of arms to reach under the drum to thread the belt onto the tensioner. The lint filter, of coarse was just a matter of throwing the old cracked one away and replacing w/ the new.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I removed the 2 screws that hold the ignighter & cover in place...unpluged the wire...replaced it with the new ignighter...thats when I found out that it was easier to take off than to put on...but I got it back into place...replaced the 2 screws...put the new belt on the drum...fitted it around the moter...pulled the wheel spring back to get it on tight...made sure the drum was fitted around the wheels...checked the tension...plugged in the wire for the ignighter...tested to see if the ignighter glowed...it did...I but the door back on the dryer...and it works...i thank my father for showing me how to work on machines...instead of letting me play with my dolls...thank you Parts select for getting my order to me in great condition & record time...
unplug dryer, lift top, remove 2 screws holding front, lift & swing front to right, use nutdriver to remove two screws holding igniter and other piece attached with same screws, a couple wiggles and out, unplugged igniter, plug in new, reposition new igniter and other piece, replace screws, repositioned front panel, replaced front panel screws, dropped top back in place, plugged in and wha-la. Heat.Original Igniter had a hairline crack in it causing it to intermittantly fire. Thanks PartSelect, right part and speedy delivery.
Easy Job.First take a flat head screw driver and pop the top placing the screwdriver in between the front panel. The top of the dryer should pop up. Then just pull it up and over towards the back.Then unscrew the front panel and move it out of the way leaveing the front door atached to the panel.Once you open the front panel' You can pull the dryer tub out by sliding it out and at the same time you need to push the belt towards the back of the tub until it comes off.Now you can get to the ingiter by first disamablethe gashousing first.Simply by taking one screw off and disconnecting the gas line fitting in front of the dryer. Also disconnect the 3 sets of wires that are connected to that piece and the igniter.The hole piece will then come out with the igniter attached to it.Next disconnect the igniter from the piece and replace it with new one.Then put back togather the same way you took it apart.Reinstalling the tub.When it's time to put the tub back in; there's a trick to that.Put tub in about 3/4 of the way in, put the belt around the tub and let the rest hang to the floor inside dryer.then crawl into the tub and stetch your head and arm through the tub on the back side.Then you can get to the belt and route it into the motor and the pully that is spring loaded it makes it so much easer that way then trying to run the belt and route it in place from the top. Once that is done now you can adjust belt back to its orignal position then push the tub back in place. Reinstall fron panel and your their.Total cost 36.00 plus shipping. Thats a lot cheaper then a sevice call and labor
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.