Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11740695
This closed hinged style bake element is 15-3/4 inches long and 16-5/8 inches wide. The terminal depth is three inches and they are 1-3/4 inches apart.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
simply removed screws & old part.., replcd new part & screwed back into place.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Could not believe that the part was here the next day! Install was simple,just connect the wires and screw it in.
I ordered part from Part Select, which literally arrived in 2 days. I unscrewed the two (2) screws holding the old bake element in the oven. Pulled out the element and detached the wires connected to the element, which was easily done without any tools. Attached those wires (again easily by hand with no tools) to the new bake element and screwed the two (2) screws back in. The whole process including ordering the part online, unpacking the box and installing took 15 minutes. Wonderful and in time for my wife and daughter to bake Christmas cookies!
My husband said HE JUST TOOK OUT A COUPLE OF SCREWS ,TOOK THE OLD ONE OUT AND PUT THE NEW ONE IN .
I took out 2 screws and installed new element! It took 5 mins.
Well it was quite simple to replace all I used was a long Phillips screw driver,the job only took me 10 minutes to complete,thank you so much for the part you sent me it was the correct part.
Don't know, left the room.
This repair couldn't be easier. I turned off power to the range, removed the oven racks, unscrewed the two screws holding the element, carefully slid the connectors off of the terminals, reconnected them to the new baking element, put the screws back in. Entire repair took less than 10 min. Not much harder than changing a light bulb. Works like a brand new oven.
Replaced broken element with new one, part was delivering quickly and work great
removed racks and door (could have left door on but made it easier to reach screws) removed 2 screws from old element unplugged the 2 wires and reversed process for new element.
I just removed two screws and disconnected the push on clips I then cleaned the botton of the oven and replaced the element. And it works just like new.
Unplug oven unit from outlet or flip the breaker to disconnect the electricity. Used screwdriver to remove face cover, pulled wire connections from posts of old bake element. Attached wire connections to posts of the new bake element(they just slip on the posts). Aligned the face cover flush with the oven wall and replaced screws to hold cover on. Reconnect electricity and ready to bake. It is very simple.... We were very pleased with how quickly the element was delivered after ordering it.
My handyman removed the old burnt our element by removing two screws and disconnected two wires and reconnected wire and screwed the unit into the oven wall. This repair was a breeze! Thanks for making my life easier!
Found breaker box and shut off power to stove, Check to make sure you turned the right breaker off before you attempt to put you hands in it, also make sure all the switches on the stove are in the off position . Open Oven Door, I used a Phillip screw driver to remove the two screws holding the Bake element in place . pull out to reach wire connections and gently pull connectors from element. Remove the old Bake element and Install the New one,by reversing process in removing the old one. after you have it back in place turn breaker back on at breaker box turn oven control to Bake setting, turn Oven Temperature control to around 200 degrees and Element should began to glow bright orange, job complete, it's that easy!~
Funny, I suppose. We decided to buy a new stove given the old age of the old one. Problem is, on delivery day it wasn't delivered and we discovered that there wasn't even one in the warehouse. At that point we got ticked and decided to look into the problem. The website led us right to the problem. We ordered, the part arrived the next day and the replacement was simple. Just unscrew the holder inside the over, unplug the old element and plug in the new. I needed needle nose pliers because one of the wires slipped behind the insulation. We also bought a thermometer and found that the calabration was right on the money. Happy campers... we saved $400.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.