Install videos!
11740613-1-M-Whirlpool-WP285655-Hose Clamp
Part Location Diagram of WP285655 Whirlpool Hose Clamp
See part 29 in the diagram
Replacing your Kenmore Washer Hose Clamp
( Grid squares measure 1x1 inch )
11740613-1-S-Whirlpool-WP285655-Hose Clamp 11740613-2-S-Whirlpool-WP285655-Hose Clamp 11740613-3-S-Whirlpool-WP285655-Hose Clamp Part Location Diagram of WP285655 Whirlpool Hose Clamp Replacing your Kenmore Washer Hose Clamp
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Hose Clamp WP285655

 Fits your DU24D4!
★★★★★
★★★★★
2 Reviews

Rated by 3 customers 

A Bit Difficult 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

$ 11.10
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your DU24D4!
PartSelect Number PS11740613
Manufacturer Part Number WP285655
Manufactured by Whirlpool
Product Description

Hose Clamp Specifications

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Kenmore Washer Hose Clamp

Replacing your Kenmore Washer Hose Clamp
Back to Top
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer, Dishwasher, Washer Dryer Combo, Refrigerator.
This part works with the following products:
Kenmore, Whirlpool, Maytag, Amana.
Part# WP285655 replaces these:
AP6007497, 01500081, 01500148, 01500206, 01500208, 01500214, 0808186, 113200354, 113200366, 14001075, 14001076, 14219080, 14220070, 14224489, 17225, 2-0461, 2-0908, 2-0909, 2-1011, 2-10597 , 2-11641, 2-14875, 2-2574, 2-461, 2-4680, 2-908, 2-909, 200461, 200908, 200909, 201011, 20211, 202574, 20391, 204680, 21001875, 21002254, 210597, 211641, 21276, 214875, 22001640, 22001820, 22001984, 22002054, 22002838, 22002853, 22003295, 22003596, 22003897, 22003933, 22004375, 23001259, 24001438, 25-6068, 25-7080, 25-7797, 25-7881, 27001024, 27001223, 27151, 27153, 272803, 272849, 272851, 272852, 272853, 272854, 272858, 27644, 285655, 287323, 288003, 288004, 288094, 29176, 29439, 326031815, 326038497, 326049294, 33748, 34-0534, 34001315, 34894, 353093, 353097, 35370, 35384, 36802, 370445, 370446, 370447, 370449, 371498, 371500, 4-10297, 40109101, 410297, 4159784, 4160500, 42011233, 42011267, 42048095, 42048116, 42048119, 42048125, 4340211, 4355207, 451200, 451201, 451202, 451203, 451204, 52754, 596592, 596595, 596616, 596727, 61001162, 614.4098, 619584, 65349, 660626, 660628, 7-57388, 7-57442, 712138, 719649, 719650, 719933, 757388, 757442, 8-8186, 80-8186, 808186, 8181753, 8182375, 8182425, 8182768, 8182906, 8317496, 8317946, 8318497, 9-10068, 910068, 9411984, 9414925, 9420906, 965289, 96739, 96991, 98014, A3326001, A3326003, DC65-00009A, M0103004, P113200366, R0000457, R0213577, R0601505, R0601515, R0601516, R0601517, R0601518, R0601519, R0601541, R0601549, R0601551, R9800067, W10112110, W10142630, W10151157, W10156063, W10245724, W10421047, W10527162, W10736530, W11375994, WP22001984, Y01500081, Y01500148, Y01500206, Y01500208, Y01500214, Y0808186, Y22001820, Y6144098, Y757388 Show less
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
3.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    1
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
David G - June 6, 2020
  Verified Purchase
Wrong size for the repair
I purchased two parts to complete the repair...the hose and the clamp. Presumably they were sold together to facilitate installation. Unfortunately, the hose clamp would have been better suited for a radiator than a washing machine(4" vs.1") Not the fault of the sales staff....they were only relying on what the merchandising staff told them.
★★★★★
★★★★★
Joseph D - February 4, 2019
  Verified Purchase
amazing results
I had a worker damage a customers washing machine. I figured I would have a hard time finding the parts as the machine was quite old. I took the make/model number went to parts direct and looked at there break downs found the parts, surprisingly they were in stock, paid for overnight shipping they arrived the next day fit perfectly, I will make part select my go to for appliance pieces. GREAT JOB .
  • 1
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.4 / 5.0, 3 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Cracked hose AGAIN!
Hired someone. Note: I purchased two (2) hoses and (2) clamps -- this is the third time I am replacing a cracked hose. The manufacturer needs to use better quality and more flexible material for hoses.
Other Parts Used:
Drain Hose with Bend and Stay Hose Clamp
  • BLANCHE from OSSINING, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
6 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leak noted on floor at front of washer and at sides
Occasional noted leak became worse and I had a repair service out. Incorrect detection of outer tub seal made so cancelled them and read comments about raising the top. Did so just at start of a rinse cycle to see soapy water shoot from top of syphon break then continue to dribble out through tub empty process--this is what had cause the water to flow down the interior drain hose and out through the side and bottom near the pump.

Ordered all the parts shown here and they arrived just in time for planned work. Did not need or use the clamp and gasket purchased as the gasket was included in the break package and I really like the old-style clamps much better.

Replaced the break and the elbow and put it back together. Things went south on a rinse as water shot out the back hose at the new elbow. I had not realized the size of the new elbow was smaller than the original. Went back to the old elbow but it bothered me that it would still move when the 4 assembly bolt-screws were completely tight.

So far this seems to have worked. There does not seem to be any leaking at all. For those who read this, the job could be done in about and hour for less than I spent if you observe and diagnose properly. It appears that the washer at the end of the Syphon Break wore out and that is what caused the leak.

Thanks much to PartSelect for being in business and to all the posters on this site for helping everyone to get these things done right!
Read less
Other Parts Used:
Syphon Break Elbow Kit with Clamp Hose Clamp Syphon Break Gasket Siphon Break Connector Kit
  • Jeff from Moorpark, CA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers, Socket set
57 of 65 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive Pump Leaked
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on.
Read less
Other Parts Used:
Drain Pump Hose Clamp Spin Belt Idler Pulley Wheel
  • Stephen from Laveen, AZ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
73 of 90 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

4 questions answered by our experts.
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Charles
October 24, 2019
Have a leak clean all the water up on floor, is dry wash cloth now don't see no water floor is dry
For model number wtw8240ywo
PartSelect logo
Hi Charles, we cannot be 100 percent certain what is causing the issue. The hose clamp part WP596669 is our best guess as to what would fix your problem. Thank you for your question and good luck with your repair!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Tim
November 21, 2021
Spin cycle has slowed down. Is there a clutch on this model?
For model number MAV208DAWW
PartSelect logo
Hello Tim, Thank you for the question. This model does not have a clutch. We suggest checking the Drive Belt for wear and the Transmission Pulley and Bearing Kit. We hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Transmission Pulley and Bearing Kit
$69.83

  In Stock
Drive Belt - 51 inches long
$10.98

  In Stock
Merrill
January 8, 2018
How do i remove the cabinet on this model of Maytag washer? I have a leak and i can't get the cabinet off to determine where the leak is coming from. It might be something as simple as a hose clamp, but i'm not smart enough to determine how to remove the cabinet. Any and all help will be greatly appreciated. Thanks for your time.
For model number mvwb835dw1
PartSelect logo
Hi Merrill, Thank you for your question. There is a video on our website that you can reference on how to remove the cabinet. The washing machine in the video may not show exactly like the one you have and the part being installed is the clutch assembly, but it will show you how to remove the cabinet. You will find the video under part number PS334641. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Jose
January 22, 2023
the water inlet do not stop hot and cold even when not workig the whasher
For model number mhw5500fw1
PartSelect logo
Hi Jose, thank you for reaching out. If your washer water inlet valve would not shut off, there are a few possible causes: damaged water inlet valve, broken water level switch, or issue with the hose clamp. We suggest that you check these parts and replace the damaged component to resolve the issue. If you require assistance to place an order, please contact customer service. We hope that helps!

Was this helpful?
Thank you for voting!
Related Parts:
Hose Clamp
$7.76

  In Stock
Water Level Switch
$55.53

  In Stock
VALVE
$128.10

  In Stock
  • 1
Back to Top
You May Also Need ?
Outer Tub to Pump Hose
$42.82
$42.82
  In Stock
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11740613
Manufacturer Part Number: WP285655
Brand
Model Number
Description
Kenmore
101963580
Washer - Kenmore Washing Machine Model 101.963580 (101963580, 101 963580) Parts
Kenmore
101963581
Washer - Kenmore Washing Machine Model 101.963581 (101963581, 101 963581) Parts
Kenmore
101963582
Washer - Kenmore Washing Machine Model 101.963582 (101963582, 101 963582) Parts
Kenmore
10682872600
Washer - Kenmore Washing Machine Model 106.82872600 (10682872600, 106 82872600) Parts
Kenmore
110088732791
Washer Dryer Combo
Kenmore
11010202000
Washer
Kenmore
11010202001
Washer
Kenmore
1101050299
Washer - Kenmore Washing Machine Model 110.1050299 (1101050299, 110 1050299) Parts
Kenmore
11010502990
Washer
Kenmore
11010502991
Washer
Kenmore
11010852990
Washer
Kenmore
11010852991
Washer
Kenmore
11012202100
Washer
Kenmore
11012502100
Washer
Kenmore
11012852100
Washer
Kenmore
11013202200
Washer
Kenmore
11013212200
Washer
Kenmore
11014102300
Washer
Kenmore
11014112300
Washer
Kenmore
11014202300
Washer
Kenmore
11014212200
Washer
Kenmore
11014222300
Washer
Kenmore
11014502300
Washer
Kenmore
11014852300
Washer
Kenmore
11015732400
Washer
Kenmore
11015842400
Washer - Kenmore Washing Machine
Kenmore
11015852400
Washer
Kenmore
11015862400
Washer
Kenmore
11015864400
Washer
Kenmore
11015942400
Washer
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
Hose Clamp
$ 11.10
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.