Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11739535
This part is used to cover up the dispenser.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Ordered the lid and it has two pins one longer and one shorter. I put the pin in the wrong part of the lid the first time, could not get the pin out--the lid was toast. Had to re-order the part and the hinge pin the second time. Easy to do if you REMEMBER where the pins go on the lid--Would have been nice to receive a paper description with the lid and the placement of the pins with the part sent, or the drawing showing the pin placement. Once the shorter pin is put in the top hinge spot--it is gone forever and will not work.The shipping and order process was flawless, the parts both times were received within two days-great service.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I took off the rear panel and removed the hose clamps and electrical terminals, slid pump out of slot in bottom pan of washing machine. It only took minutes, this was part of a major overhaul. I replaced this as a precautionary measure. Great prices and quick service,
Removed 4 screws holding dispenser frame. Removed old & installed new frame. Top, hinged lid needed to be slightly bowed so hinge pins could be fit in holes. End of repair.
An earlier post saved us an awful lot of time and effort by mentioning the importance of holding on to the original pins for the hinges because they are not included in the lid replacement provided by the manufacturer. Great site. Thank you.
First I removed the 4 screws that kept the bezel in place, removed the bezel. Replaced the new bezel, replaced screws, put new top pin in door and put door on.
Remove part from package. put in place. press in pins. done. Now I'm ready to fix the tub bearings and the wax motor ! save $500 or more.
There was 4 screws that held the bevel in that still needed to be removed from the old broken one. Once we removed those we were able to place the new bevel and lid in the correct sport, replace the screws and viola, perfect.
The soap dispenser is held to the washer body by means of the bezel and four screws. In my case, the bezel had broken at two corners, allowing the soap dispenser to bang around during spin cycle. In addition, the dispenser lid had broken off, and the hinge pins were missing. NO PROBLEM! Step 1: Remove (and save) four Phillips head screws, and discard broken bezel and lid. Step 2, Using old screws (or new ones from the hardware store -- just make sure they are stainless steel), fasten bezel to soap dispenser at all four corners. Don't over-tighten. Just make it snug. Step 3: Insert short pin in short socket in lid, and slide long pin into the long socket -- the one open at both ends, with a groove to allow it to slide back and forth. Step 4: Seat the short pin in the rear socket in the bezel, slide the long pin inward allowing the lid to seat into the bezel, and then (using screwdriver) gently push the long pin through and slide it into the front socket in the bezel, forming a hinge. DONE! No more banging. This 15-year-old washer should be good for many more loads. Thank you, !
First off, unplug the machine. Next remove the existing screws in the plastic dispenser. Then remove the door, there are two screws holding the door on connecting two brackets which need to be lifted to get them to release. That gives you the access to the remove the front panel, which is done by pulling on the panel itself. Once that is done you need to remove the two screws that are in the corners upper left, and right that are holding the brackets that hold down the top of the machine. Remove the brackets by gently turning them. Once done the lid should easily lift up. The dispenser can then be disconnected by removing the 2 rubber hoses on top and the the larger rubber hose on the bottom along with the electrical connections under the unit. Keep track of which wire goes to which lead. After removing the dispenser just do everything in reverse. The machine is like new, and the repair took about 45min and saved me at least $200 dollars.
I got the part, but it did not come with the pins needed to insert into slot in washer. I had to go to Lowes and buy some pins and improvise to make them fit on both ends. It is working well....Probably saved myself $100.00 (service call etc) Thanks
I removed the dispender assembly from compartment. (Four phillips head screws.) Attached new lid to the dispenser housing. Cleaned the surface where assembly had been sitting on. Reattached the assembly unit to the washer. Looks good!
Removed 2 of 4 the screws that were holding the Dispenser Bezel in place. Removed the broken Dispenser Bezel and the other 2 screws. Cleaned the 4 screws (remove the detergent) cleaned the inside of the Dispenser area. Assembled the Dispenser lid /bezel assy. Secured the lid / bezel assy to washer with the 4 screws. Installed the syphon cup and syphon cap.
removed 4 screws and installed pin in new lid to base and installed part back on washer with 4 screws. Parts arrive in a timely fasion. good sservice
removed bezel, 4 screws, underside of lid has clues to which pin goes where, short or long noticed one hole for pin is "bored" through so pin can be pushed through used a nail if nothing else flatten point BE PATIENT DON'T PANIC
Slightly bent the plastic lid to allow the pins in each end to slide into place
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.