Quick Question!

Have you ever purchased from PartSelect.com before?

11739426-1-S-Whirlpool-WP22003285-Tub to Drain Pump Hose
11739426-1-S-Whirlpool-WP22003285-Tub to Drain Pump Hose 11739426-2-S-Whirlpool-WP22003285-Tub to Drain Pump Hose http://www.partselect.com/Schematics/Maytag/52404.gif

Tub to Drain Pump Hose

PartSelect Number PS11739426

This tub to pump hose is thirteen and a half inches long. It is all black in color and is made of plastic.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.

Compare At

$18.74

You Save

$3.12

Your Price

$15.62
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 6 reviews What's this?
1-6 of 6
 

18 of 23 people found this instruction helpful

Parts Used:
  • Tub to Drain Pump Hose
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers
Customer: Brian from Lynbrook, NY

Leaking pump hose

I thought I was going to need to replace the leaking washer machine. Water was every where and after checking the main sewer drain was ok I lifted the washer and found the water pouring out the bottom when i put it on.
After finding out how to get the whole top open and the front panel off I was able to locate the source of the water leak on my washer machine. The cause was split in the plastic hose that goes from the tub to the pump. After the new hose arived I was able to replace it within 10 minutes. So far so good. Thank you Part Select.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 10 people found this instruction helpful

Parts Used:
  • Tub to Drain Pump Hose
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Richard from Cedar Park, TX

Water leaking under washer. Tub to pump hose sprung a leak.

There are two clips that hold the top of the washer down. Releasing these clips allows you to lift the top; it is hinged at the back. Then remove two screws holding the front panel and remove the front panel. The tub to pump hose is easily accessible. It is held in place by a hose clamp at each end. Use pliers to squeeze the clamps and remove the hose. Replace with new hose. I re-used the original clamps.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 4 people found this instruction helpful

Parts Used:
  • Tub to Drain Pump Hose
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers
Customer: JERRY from LEXINGTON, NC

Washer was leaking when water was pumping out

Took a putty knife and raised the top,then took two bolts out, then pulled front panel off. Took hose off from the tub to the pump,and put the new one on. It's working fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 4 people found this instruction helpful

Parts Used:
  • Tub to Drain Pump Hose
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Huston from columbiana, AL

Water in the floor

take a butter knife and pop the clips loose on the front between the lid and the front take the two screws loose on the front in each corner remove the front cover and you will see the hose take the clamps off and replace the hose

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Tub to Drain Pump Hose
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers
Customer: Russell from Aplington, IA

Water on the floor

figured out how to open the top of the washer(Two small tabs I pushed in with a putty knife. Looked for the area it was leaking. Slide the hose clamps off with a pliers and pull out hose.

Put clamps on new hose, replace hose and slide clamps to ends to seal the connections

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 8 people found this instruction helpful

Parts Used:
  • Tub to Drain Pump Hose
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: william from norristown, PA

Water leak

pop top,remove 2 screws,remove front panel.remove 2 spring clamps from tub hose.reverse!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-6 of 6