Quick Question!

Have you ever purchased from PartSelect.com before?

11738945-1-S-Whirlpool-WP216201-Rubber Injector Valve
11738945-1-S-Whirlpool-WP216201-Rubber Injector Valve 11738945-2-S-Whirlpool-WP216201-Rubber Injector Valve http://www.partselect.com/Schematics/Maytag/37308.gif

Rubber Injector Valve

PartSelect Number PS11738945

This part is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle. It is black in color and measures approximately 2 inches in length. To access this part, you will need to remove the front panel of your washer. There will be 2 screws holding it in place. Once these have been removed, the top will pivot to open, which will give you access to the injector assembly. This is an OEM part that comes right from the manufacturer and is sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.

Compare At

$12.67

You Save

$2.11

Your Price

$10.56
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 62 reviews What's this?
 

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Cindy from Jim Thorpe, PA

Water was flowing from the side as it would fill

remove the front and opened the top, removed the old parts and added the new plus a new clamp that I purchased from the local store.
I'm a single mom, one income so doing repairs myself is very important. The parts came when promised and it cost me about $23.00 where a repair man could have charged me well over $100.00 just for the parts.
First time I used this website or ordered parts, I will definitely do it in the future.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Mike from Waverly, TN

Water was over flowing the holes that are built into the sleeve. Causing water to leak out on to floor.

Took the front off the washer. Removed the two screws that hold the top down, this allows the top of the washer to hinge back. The two hose clamps are removed, the hoses slide off the sleeve giving access to the injector and the valve.The new injector has to be placed in the rubber valve and then slid into the plastic sleeve. Tighten up hose clamps and replace top and front of washer. Sleeve had a little different design than orinigal so I figure Maytag had seen this problem before. Almost so easy a caveman could fix it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Terry from St.Louisville, OH

Water leaking from top of machine during filling

Disconnected the the power and inline water hoses. Slid machine from wall about two feet.Removed the two phillips screws in front panel. Removed the two 7/16 hex head self tapping screws one in each side panel to the top. Raise the top section.The parts I replaced were on the top left side of the drum. Loosen the claims and remove the old parts. Really easy!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Ronnie from Fayetteville, PA

Water leakage

First I removed the front panel. I then lifted off the top of the washer to gain access to the injector valve and nozzle. Then I unscrewed the retaining clips on the hoses joining the injector valve and nozzle. I separated the hoses from the injector valve/nozzle assembly. I then replaced the injector valve/nozzle assembly with replacement parts and reassenbled.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Wrench set
Customer: Tina from Enigma, GA

Water pouring out instead of going into tub

watched the video on the site and went at it. lol Repair was fast and easy , almost 30 yrs old and still washing like a charm! Mite be the last one made in America !!!!! Too bad!
Thanks for the help and will def recommend the site to friends. I actually got it from a friend

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Wrench set
Customer: Richard from Ridgefield, CT

30 year old washer started to leak on left side

Noticed small pool of water on left side. Diagnosed it was injector tube. Ordered parts.

Removed front panel by removing two phillips screws and then pushed down to disengage spring clips.

Used nutdriver to remover two bolts holding top cover and then undid bleach dispenser hose.

Lifted top cover and removed clamps holding injector and fill. Replaced using 1 1/16" Stainless steel screw clamps.

THIS WAS THE FIRST REPAIR EVER ON THIS WASHER!! SIMPLY AMAZING PERFORMANCE. STILL SPINS AT HIGH RPM AND IS QUIET. Bought for my folks as a gift in 1979.

This is the reason I bought the last Maytag top loaders made in '05. Also had another one 24 years with only one repair.

Parts Select, thank you! Parts arrived in three days.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Wrench set
Customer: Ed from Paoli, PA

Leaking washing machine

After reviewing the diagrams and instructions on your site, I unscrewed and removed the cover to the washing machine. I located the source of the leak and replaced the aged parts. I put everything back together and voila, no more leak. Thanks!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers
Customer: Richard from Houston, TX

Water leaking onto the floor while washer was filling.

By removing the front panel and raising the top panel, I was able to observe that water was overflowing from a small plastic "cup" that was positioned midway along the inlet lines for water entering the washer tub. None of the adjacent parts were visibly damaged or broken, but the rubber ones were soft and "gummy" to some degree. I ordered the three parts that I was able to identify, based on the photos at PartSelect.com. They arrived ahead of schedule and I was able to install them the same day. The only additional disassembly involved disconnecting the hot and cold water lines, removing the water inlet shield and gaining access to the upstream end of the old rubber hose in order to replace it with the new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: Jon from N.R.H., TX

Water on floor when filling

removed front panel, lifted top of washer and tilted back,pulled black fill hose off clear plastic vent,pulled worn retainer out and put new one in.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Rubber Injector Valve
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Jonathan from Jacksonville, AR

Washer was leaking immediately as it started filling.

I removed the front panel and discovered the general area of the leak. Raised the top and found the injector valve had a hole in it. Removed the injector valve by removing the collar closest to the front of the washer. Searched the internet and found the PartSelect website. To my delight, not only was I able to order the part on a 27 year old washing machine, but there was also a 10 minute video on how to replace the part!! Although my wife was not terribly interested, I kept telling her how cool it was that there was a video showing how to replace this part. I think she was hoping this leak meant a new washing machine. Anyway, part replaced following the directions in the video and the old washer is fully functional again. Thanks for the awesome website!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Elzo from Kalamazoo, MI

Leak coming from underneath washer. Source unknown

Removed front panel ( 2 swrews). Turned off water to washer. Unplugged power cord. Removed two screws holding down top of washer. Located source of leak. It was the injector valve. Removed hose clamps. Removed defective injector valve (2 parts). Installed now injector valve (2 parts) as shown in video. Tightened hose clamps. Replaced top cover and front panel. Done

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Rubber Injector Valve
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Alan from Timonium, MD

Injector valve sleeve developed hole over many years.

Repair was a cinch, following this great video: http://www.partselect.com/PS2019175-Whirlpool-216201-Rubber-Injector-Valve.htm?SourceCode=1&SearchTerm=a712&ModelNum=a712#RepairVideo

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Socket set
Customer: Ronald from Buford, GA

Minor water leakage visible on floor on left side of washing machine.

I opened up the front panel of the washing machine and noticed that water was leaking from a hose along the top left of the machine. I ordered a new plastic injector nozzle and rubber injector valve. The parts arrived in 2 days. Switchout of the parts took less than 5 minutes. Tested it out; the leak was gone. Total cost $22.62. Money well spent!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Richard from Nashville, TN

Water leaking

Followed repair guidance provided on website: 1) Removed front panel of washing machine by removing two phillips-head screws (bottom front of machine) and lifting front panel from bottom. 2)Removed two hex-head from front corners of top panel. 3) lift front panel to gain access to Injector Valve and Nozzle. 4) Removed hose clamp, removed hose, removed old valve and nozzle. 5) Replaced components in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Socket set
Customer: Chris from Atlanta, GA

Leaking

First removed front to see approximately where the leak was - left side from the front. Parts arrived quickly. Removed top and swung up to the left side (not the back). Video was very helpful at showing how to replace valve and nozzle. The old valve did indeed have a hole in it and the injection had some perished rubber slime. Closed back up. Hit snag - the top loader door latch was not engaging preventing the machine operating. Hmm. Opened up again and with flashlight located sound of buzzing relay (being careful since the machine was powered) Noticed a wire was caught up in the relay. Disconected power. Re-sited wire and used a twist to hold to other wires to keep it out of the way of the relay. Closed back up. Everything fine. So glad to keep my 24 yr old machine going! Amazing that this was the first time it had ever been moved and opened up. Moving and cleaning was be far the longest part of the whole operation. Great site.

Help other customers find the most helpful instructions.

Were these instructions helpful?