Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11738836
Hoses are the most likely cause of clothes washer leaks. This tub-to-pump hose carries the water from the tub to the drain pump. If you notice that your tub is leaking during the wash cycle, check the the hose for holes. If the tube does have a hole or crack in it, the part should be replaced. Also, check both the connection and the juncture of the hose with the drain for your house. While you are looking at the hose, check to see if the threads or clamps are corroded or loose. This OEM replacement pump hose is 20 inches long, and fits most clothes washer units. Remember to turn off the water supply and disconnect the power from your washer before you begin this repair.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I brought the wash machine out side, hooked a garden hose to the cold, capped the hot, took off 2ft. square back inspection cover, and plugged in the power cord for a test for leakage location. The hose from tub to pump had a small wear hole, thus leaking water on the belt and making it slip more. When my parts came in from Parts Select the repair was about 45 mins. with coffee. I laid unit on side, cleaned pulleys with rag to remove old belt fragments, and I put new belt on the 2 small pulleys then rolling onto last bigger pulley. For the hose repair- I used a screwdriver to push in the clips under front of top lid. I removed 2 screws with my 1/4 rachet to remove front panel. With my channel locks I pulled off hose , then installed new hose. The unit works great.
Help other customers find the most helpful instructions.
Were these instructions helpful?
After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was simple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.
Took off the back plate. Looked to see where it was leaking. Squeezed the clamps on top and bottom to remove from hose and pull hose out.
removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..
Replaced the hose. two clamps and retainers. very basic repair
The Repair went well . I had the hose on in about 30 seconds . The best part about this ordeal was the ease of finding the part on your website , and the speed of the delivery . I had my part in about 2 days , put it on and back to the fun part of clothes washing . I would recomend this company to everyone. Thanks, Rick K.
Removed back access cover and lift top cover looking for leak. Initially thought it may have been the pump housing. I filled some water into the tub and I flexed the hose between the tub and the pump and water sprayed out. It had cracked in about 3 small places (water is present in the hose anytime water is in the tub) Ordered and replaced hose. Also order drive belt and replaced as a preventive maintenance item.
We have a Jenn-air washer & dryer that we bought new & are now almost 15 years old. I just put about $20 into the washer that took me about 20 minutes to do the repairs. Change tub to pump hose & lid hinge pins. The dryer was about $40 to fix. Blower wheel & drum rollers. That repair took about 40 minutes. Both units you have to take the front cover off & that will expose just about everything. A screw driver between the top & front will pop them open. One hour & $60 in 15 years. I think we made a good choice.
Remove the metal plate in back of the washer that 3 screws. I use a vise-grips to remove the two clamps.One on other the tub side and the other the pump side. Pull the old hose off the tub side and the pump side.Use the old clamps to put the new hose on.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.