Quick Question!

Have you ever purchased from PartSelect.com before?

http://www.partselect.com/Schematics/Maytag/43432.gif
See part 11 in the diagram
http://www.partselect.com/Schematics/Maytag/43432.gif

Timer - 60Hz

PartSelect Number PS11738812

This timer assembly has a quick wire harness connector. Notes Because there are so many different timers, you should use your model number to make sure this is the right timer for your washer.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

Compare At

$204.35

You Save

$34.06

Your Price

$170.29
Order within the next 1 hr and 54 mins and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 5 reviews What's this?
1-5 of 5
 

6 of 8 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Joshua from Midlothian, VA

Washing machine would not rinse or spin out

I removed the panel off of the back of the control panel by removing 3 screws along the bottom and two on the top. I then removed the knob on the front of the timer. I was then able to remove the timer by taking out two screws that were holding the timer in place from the front of the control panel. I then disconnected the bad timer and connected the new one and put it all back together. Easy fix!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Ted from Decatur, TX

Washer would not spin or drain

Could manipulate symptom by putting pressure on old timer knob(to help diagnose as a timer fault). Removed knobs from front of panel, removed 5 screws to remove faceplate of panel. Removed 2 bolts and 1 wiring harness connector for access to replace the timer control. Reassemble and function test. All normal functions. Took about 20 minutes total.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Douglas from Chesapeake, VA

Timer was not functioning properly

Removed the outside face and dial, and then removed the control panel by removing two screws.
Unplugged the timer and removed the two screws holding the timer in place.
Reversed the process to install the new timer.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 5 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Dan from Cumming, GA

Washer won't spin out and drain on last spin cycle

behind the timer dial there are five 1/4 socket nuts, remove them. Then turn off your water supply and push in the dial and turn it counter clock wise and it will un screw. Next pull the dial indicator off and ther are two other screws (size unknown) unscrew them and the timer comes out from the rear. simply unplug the connector . Plug in the new timer and reassembly. My son and I had it removed and installed in under ten minutes. easy. and works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 3 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: jerry from east carondelet, IL

The washing machine would not spin, it would only spin on delicate cycle.

I knew right away it was the timer. I removed 3-1/4" bolts from the very top/back side of the washer, and 4 screws from the bottom of the control panel, 2 screws in the front side, and 2 screws in the back side, at each end of the control panel.make sure the timer knob is pushed inward, turn it counter clock wise to unscrew it off, then pull the back plate knob back towards you, it will pull straight off. then pull the other 2 knobs straight back towards your self, and they will pull off. then you can remove the control panel cover ! Remove the 2 bolts that hold the timer in, then pull the timer out through the top of the washer. Then unplug the wire harness from the timer. And it's out ! This did not take long to do ! Just reverse these steps to put your back together !

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5