Quick Question!

Have you ever purchased from PartSelect.com before?

11738577-1-S-Whirlpool-WP12665101-Ice Chute Seal
11738577-1-S-Whirlpool-WP12665101-Ice Chute Seal 11738577-2-S-Whirlpool-WP12665101-Ice Chute Seal http://www.partselect.com/Schematics/Maytag/57962.gif

Ice Chute Seal

PartSelect Number PS11738577

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

Compare At

$5.32

You Save

$.89

Your Price

$4.43
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 5 reviews What's this?
1-5 of 5
 

8 of 11 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Janet from Edmonds, WA

Water dispenser got stuck on one function, couldn't get water to work

Removed two screws and took off water dispenser front panel. Unplugged wires to old control board and removed it from brackets holding it to inside of dispenser panel. Aligned and pushed new control (with care to only touch the outside edges of board...cannot touch circuitry which will permanently damage it). Was tricky aligning the board and snapping it back on, but finally got it in place. Repositioned dispenser panel and reattached two screws.
Second problem was the Chute and chute seal had broken off from the hinge chute so it wouldn't open or close when dispensing ice. Was pretty tricky to realign the chute seal to the hinge, but with some paitence and manipulation, was able to reconnect them.
I am REALLY impressed with the detailed drawings I found on PartSelect.com's website. Without these drawings it would have been difficult for me (my husband and son put the parts in, I did the ordering) to know what parts to order. Service was EXCELLENT. I would definitely do business with this company again. Great work!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Clifford from Madison, IN

Ice maker door broke allowing open hole to freezer

The ice maker panel on the freezer door detaches by removing two screens at the bottom of the panel behind the drip tray. My son held the panel while I removed three screws holding the ice chute cover. The ice chute door is attached to a spring loaded bracket. I only needed the actual door, but it was just as easy to replace the insulation and the seal. The seal was starting to show wear. I then replaced the ice chute cover and tested the ice maker. With everything working correctly, I reinstalled the panel in the door.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 13 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Ralph from St Petersburg, FL

Ice cube door not shutting

Took the front panel off,replaced the parts inside on the door ,Replaced the panel ,Tested
Now found out that it is the solniod that is bad ,Part on order ,Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?   

44 of 709 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: LORIN from PHILADELPHIA, PA

Significant frost forming on ice chute.

Following diagram on website, I removed the 2 screws on the face of freezer door ice dispencer.Removed old chute door and solenoid. Replaced with new. I purchased all parts involved because they were inexpensive. The issue was most likely the solenoid.After installation ,the chute door had a sound of being positively closed by the solenoid.I\Frost no longer forming!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

77 of 1254 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Joe from Strongsville, OH

Ice build up in the dispenser chute

removed the spill tray, then two bolts. removed ice dispenser assembly by removing 3 more bolts. changed the seal and the insulation and reimstalled unit in hte reverse order. works perfectly -no more ice build up in the chute.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5