Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11738134
NOTE: This part has been updated by the manufacture and now includes both left and right side.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
First I removed the pantry drawer; then the two crisper drawers and glass shelf. Then I removed the hex screws that held end cap in place. Removal of cap from refrigerator was complicated by the adjustable temperature control - it is loosely attached at the back of end cap and also has to be removed to get cap out. Gentle persuasion accomplishes this. Getting the slider off end cap also a bit difficult. Then I removed the drawer glides. Reversing all steps was fairly easy and the rest of the "fix" went well. I wished that there had been some written directions - or at the very least, a diagram of how all went together. All in all was still cheaper than repair person.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Removed the food bins and lower shelf. Unscrewed the end cap. Removed the drawer hinge. Re-installed hing on new end cap. Installed the new end cap. Re-installed drawers and shelf. DONE! Great graphics on the website helped to correctly idenitfy the required part. Part arrived quickly and well packed. One of the easiest transactions ever!
Really easy - Remove drawers, remove glass shelf and associated support rails, remove drawer slide from old endcap, remove old endcap, reverse proceedure installing new endcap - now the hard part, have a cool softdrink while you carry the old endcap and packing material from the new one out to the trash.By the way - the part got here really fast - thanks for the great service.
Took the food out. A couple of screw removals. Put drawer lid on and then put the screws in. Nothing to it.
Wasn't a big deal. Removed the the shelves and glass immediately above the endcap as well as the large 'goumet' draw. Used a nutdriver to remove two screws. Popped off the old endcap and did everything in reverse. Replaced the long clear goumet draw cover that was still intact. Thanks for making it easy!!!!
took out the drawers and glass shelf and unscrewed the sides took parts for drawer glide off put them on the new part reinstallled saved $110 service cll and $20 on the part!
I ordered the part and it arrived in about 5 days. I removed the two lower crisper drawers and the glass shelf seperating these from the Wide-N-Fresh compartment, to give me room to work. I removed the two screws holding the right side endcap in place. The temperature adjustment mechanism was a bit tricky to remove from the broken endcap and replacing it on the new endcap. Once that was figured out everything fell into place and the lid was snapped into place and worked properly
Receive part in two days. Super fast.Repair was very easy. Whirlpool designs so even the "average joe" can fix it. Took abour 20 minutes to repair. Even with no directions.
I replaced both side. The left side I very easy to replace. It has 2 screws holding the end cap in place and the tracking has 2 screws holding it in. Undo the 4 screws and put the track on the new end cap and then you are good to go to install the new end cap on the left side. Now for the right side is easy, but you now have to also undo 2 screws and other 2 for the track just like left side but also you are going to have to undo the humidity control stuff and put it on the new end cap.
Pretty simple, remove the pantry lid, drawers above glass pantry cover and then the glass cover and its metal supports.Then the pantry tray from its metal slides.Remove the slides then the broken end cap.The slides and end caps are attached with 1/4 inch hex drive screws.I did notice a small change in the new end caps which will improve the strength of the problem tab. I do not expect the same problem again.
It took longer to empty the items off the shelf than it did to do the repair. Slid the veg, drawers out, set them aside.Took glass shelf out set it aside. removed three screws with 1/4in socket. Removed end cap. replaced with new end cap, replaced screws, cleaned and replaced shelf and drawers. Was a very easy task. these pegs break very easy, this is the second time I have had to replace the end cap, both times it was the left size. problem is you have to buy both the left and the right side together,
Replaced both sides because they had been reworked to strengthen the hinge portion !! the most important thing to do is to pay attention on how you take it apart and reassemble. Trying to take short cuts only cost you more time taking it apart and doing it again :0) Enjoy
I removed the pantry door, the pantry drawer and the glass shelf above the pantry drawer. I removed 2 screws/bolts from the left side end cap and removed it. I simply installed the new pantry end cap with the 2 screws/bolts and tightened them snuggly. I then replaced the pantry drawer ...installed the glass shelf...reinstalled the pantry door and that was it...the wife took over after that
disassembled drawers, cleaned drawers, reassembled drawers
Removed three screws and removed endcap LH and screwed sliding shelf bar two new endcap and reinstalled end cap in ref.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.