11728056-1-S-Whirlpool-W10841094-Burner Receptacle
11728056-1-S-Whirlpool-W10841094-Burner Receptacle 11728056-2-S-Whirlpool-W10841094-Burner Receptacle 11728056-3-S-Whirlpool-W10841094-Burner Receptacle http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/44177.gif

Burner Receptacle

PartSelect Number PS11728056

Manufacturer Part Number W10841094
Manufactured by Whirlpool

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Element will not heat.
  • Compare At

    $9.79
  • You Save

    $1.63
  • Your Price

    $8.16
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 43 reviews What's this?
 

4 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerPatti from Burbana, IL

Sparking burner

Followed instructions from previous repair story!!
Pulled old burner out. Unscrewed plug element. Cut old wires back about 6 inches from plug. Attached new part with wire nuts provided and covered with shrink sleeves provided. Attached plug with provided screw and slipped in new element. Works great!!
I want to thank the previous posters for posting their detailed repair stories....without reading those, I may have called a repair service and paid big bucks. Thanks to all previous posters for the detailed information they provided!! PS...The parts arrived in amazingly quick!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDavid from Jefferson Hills, PA

Intermittant heating, arcing in the socket

Simple to do. Remove old element, remove screw holding socket, cut the socket wires with 2 inches to spare, assemble the newsocket and wires with heat shrink tubing, strip range wires, apply the wire nuts as instructed and shrink the tubning with a heat gun.

Screw on the socket to the range. Shut the lid and install the element.

The replacemnet screw is thicker than the original one, so you might want to drill out the hole very slightly. I did not but the resistance was high on getting the screw fully seated.

Works great

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Burner Receptacle

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerGAIL from ORCHARD PARK, NY

Front burner would not heat

I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Burner Receptacle

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDonald from Milford, MI

Burner inop

removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Burner Receptacle

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerNancy from Baldwinsville, NY

Burner would not heat up.

Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

Help other customers find the most helpful instructions.

Were these instructions helpful?