Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11725221
If you are having trouble rolling your dishrack in and out, there could be an issue with the rollers or axles. Check the existing rollers and axles for any visible physical damage. Look to replace the parts if the rollers or their axles are damaged. These rollers attach to the dishrack allowing the rack to roll in and out with ease. This pack includes 8 gray rollers measuring at approximately 1.75 inches L x 0.75 inches W x 1.75 inches H. Each roller comes with an axle.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
but axle on new wheen and put axle on tray
Help other customers find the most helpful instructions.
Were these instructions helpful?
I had no problems at all. The old wheels had already fallen off. All I had to do was put the wheel axel into the wheel and slip it over the wire support for the wheel. No fuss - no muss - no problems.The only problem I had with this repair was trying to find the wheels and axels for the job. None of the supply houses around here had them and no one was offering where I could find them. Sooo, I went on line, found your ad, pulled it up, input my model number and lo and behold -- there they were. Thanks.
I had called the manufacturer and their prices were outrageous and I still didn't have the part numbers. The partselect.com website was so easy to use that I instantly looked at the line drawings and was able to figure out what to order. It was a snap and I am not the most handy person. Their prices were good, and though I paid for the cheapest shipping, I got the parts the next day, which shocked me. They were an excellent company to deal with.
Removed empty basket from dishwasher. Placed basket upside down and removed remaining wheels from basket by detaching worn axel from attachment points. ie, No tools needed for this procedure. Once axel and wheels were removed, I squeezed the end of the old axel with needle nose pliers or regular pliers to relieve the outward pressure and pushed the old axel out of the wheels. Easy, popped right out.Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel andattached it to the basket at the original position. New axel grips the basket like a clothes pin would.Continued and replaced all eight axels at this time.Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.Will definately re order again if needed. Thank You.
I simply removed the old (broken) stud rollers by pinching them with a needle nose pliers and pushing them out, snapped the new stud roller in the wheel, and snapped the wheel onto the lower basket unit. If you have all of the wheels and they are in good shape, you do not need to buy new wheels, the new stud rollers work just fine with the old wheels.
Removed the lower rack, removed all of the plastic wheels and axles, mounted the new wheels on the new axles and put them on the lower rack, reinstalled lower rack. Very easy and simple.
My husband was able to remove the wheels that were bending from the dishwasher rack. Then, he replaced the wheels with new ones and used new studs to hold the wheels in place.
Installed new roller which where larger than the original rollers. I believe these larger rollers will stop rack from slipping down near heating coils.The new rollers snapped on with very litlle effort.
It was sooo easy, I can't believe I took so long to get these new rollers and studs. Shipment arrived in 2 days, I removed those old melted wheels, through them away and installed the new ones, took me less than 10 minutes, it was painless, no tools needed. I did follow a tip from a buyer that was to attach the studs to the wheels prior attaching them to the lower rack and it was a very usefull tip. Do that! Now my dishwasher is like new again. Great shopping experience, Thank you!
This was a simple part swap. The stud rollers are the small peg-clips that hold the wheel on the lower dish rack. Removing the old stud rollers from the wheels required a pair of pliers. I then popped the new stud rollers into the old wheels and snapped them back onto the lower dish rack. I scored some major points from my frustrated wife -- easy, fast fix!
Man, if you need help doing this repair, you shouldn't even own a dishwasher, much less a house. This was the easiest repair in the entire galaxy. First, I removed the old wheels, which was easy becasue they were always falling off by themselves. I then had to use pliers to squeeze the old studs to remove them from the wheels. All the wheels were still in good shape. Then I snapped the wheels onto the new studs, and snapped the studs onto the lower rack. And then, it was like I was in heaven. Bluebirds were singing, the sun was shining, my lower rack was sliding in and out and in and out like it was new. O happy day.
Removed the existing stud rollers with the wheels attached. Then removed the wheels from the stud roller. Then snapped the wheels on the new "Better Designed" stud rollers. Then easily snapped the new stud roller assembly in place. Piece of cake...works like a charm.Thanks,Randy
We received our parts for our dishwasher within 2 days. It was very simple to find the parts on your site, and very easy to install. Our dishwasher is back to normal and the racks roll in and out easily. I would recommend ordering from PartSelect to anyone.
just exchange new wheels with new studs and popped back in. only thing I needed was to know that mfg had redesigned stud and replaced with quote a better mouse trap.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.