Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11725221
This includes eight rollers with axles.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
Just snapped the stud roller through the center of the wheel and then attatched it to rack.
Help other customers find the most helpful instructions.
Were these instructions helpful?
replaced clips that were much better made.
I unplugged and removed my dishwasher and followed the instructions extactly repairing the pump and replacing the parts I had just received. I torgued the ring to the specified amount, installed the pump and found the impeller could not turn. I dis-assembled it all again and loosened the ring to allow the impeller to turn, reinstalled it and when I initiated the wash cycle, water began running wildly. Next step, replace motor and pump as the pump motor shaft has gone out
Install the rollers on the studs first, then snap the assembly onto the tray. Really easy.
The repair is just a couple of minutes job. All I had to do was to pop the wheel axle in the new wheels, remove the old wheels and put the new ones in. The wheel axles on the original one, were like clasps. All one needs to do is to pull the clasp to one side and slide the wheel out. The new one, just needs to be pushed in. In my case, I could have just swapped out the axles, but decided to change the whole set anyway.
Really all it took was removal of the old wheels which would not stay on anyway and the installation of the new ones. That required the axle and wheel being put together and the installing both of those on the lower rack. I was about to buy a new dishwasher when the salesmen told me about a product called Lemi Shine it saved my hundreds of dollars and the inside of my dishwasher looks brand new. With my new wheels I am good to go again.
Removed and replaced all rack wheels with new wheels and wheel axles. All I needed was new axles, as they are new and better, and solved the problem of the wheel falling off. G.E. should offer customers with this problem, new wheel axles at no charge, as they are very easy to exchange. The original axle was a bad design.
Simply pull out the old axle and snap in the new one. It is simple. Also the replacement axels were MUCH better quality than the originals. The bottom tray now slides in and out very easily. Note, if you have this problem, you do not need to replace the wheel, just the axle.
these appeared to be a newer design of wheels and wheel hubs that fit much better and seemed more stable. Very easy to replace and the bottom rack of our dishwasher works great now!
but axle on new wheen and put axle on tray
I had no problems at all. The old wheels had already fallen off. All I had to do was put the wheel axel into the wheel and slip it over the wire support for the wheel. No fuss - no muss - no problems.The only problem I had with this repair was trying to find the wheels and axels for the job. None of the supply houses around here had them and no one was offering where I could find them. Sooo, I went on line, found your ad, pulled it up, input my model number and lo and behold -- there they were. Thanks.
Removed and replaced damaged wheels. Parts came in on time and saved lots of money on a repair rip off artest.
Removed empty basket from dishwasher. Placed basket upside down and removed remaining wheels from basket by detaching worn axel from attachment points. ie, No tools needed for this procedure. Once axel and wheels were removed, I squeezed the end of the old axel with needle nose pliers or regular pliers to relieve the outward pressure and pushed the old axel out of the wheels. Easy, popped right out.Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel andattached it to the basket at the original position. New axel grips the basket like a clothes pin would.Continued and replaced all eight axels at this time.Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.Will definately re order again if needed. Thank You.
I simply removed the old (broken) stud rollers by pinching them with a needle nose pliers and pushing them out, snapped the new stud roller in the wheel, and snapped the wheel onto the lower basket unit. If you have all of the wheels and they are in good shape, you do not need to buy new wheels, the new stud rollers work just fine with the old wheels.
Removed the lower rack, removed all of the plastic wheels and axles, mounted the new wheels on the new axles and put them on the lower rack, reinstalled lower rack. Very easy and simple.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.