Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11725221
If you are having trouble rolling your dishrack in and out, there could be an issue with the rollers or axles. Check the existing rollers and axles for any visible physical damage. Look to replace the parts if the rollers or their axles are damaged. These rollers attach to the dishrack allowing the rack to roll in and out with ease. This pack includes 8 gray rollers measuring at approximately 1.75 inches L x 0.75 inches W x 1.75 inches H. Each roller comes with an axle.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
The old wheels and attachment brackets were easily removed since they were always falling off. I ordered all new brackets and wheels, but it turns out I didn't need new wheels. If your original wheels are in good condition, they are the same size as the new ones and fit the new brackets. The new attachment brackets are built differently than the ones that came with the dishwasher, but (a good thing considering the originals only lasted 1 1/2 years). The new brackets and wheels snapped together and snapped into place on the dishwasher in minutes--no tools were needed. It took longer to cut the parts out of the packaging than to install them. The bottom rack now rolls out like it did when it was brand new. Definitely worth the few dollars in parts.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I ordered a set of 8 studs and rollers as recommended in some of the other reviews. First, I inserted the stud into the wheel PRIOR to putting the set on the rack. This was a simple repair and makes all the difference in the world for a stay at home mom who runs the dishwasher twice a day.
Just snapped the stud roller through the center of the wheel and then attatched it to rack.
replaced clips that were much better made.
I unplugged and removed my dishwasher and followed the instructions extactly repairing the pump and replacing the parts I had just received. I torgued the ring to the specified amount, installed the pump and found the impeller could not turn. I dis-assembled it all again and loosened the ring to allow the impeller to turn, reinstalled it and when I initiated the wash cycle, water began running wildly. Next step, replace motor and pump as the pump motor shaft has gone out
Install the rollers on the studs first, then snap the assembly onto the tray. Really easy.
It couldn't have been easier. I installed the new wheels in seconds and the rack glides as perfectly as the day it was installed 11 years ago! Perfection! Your stellar website made it so easy to find the correct parts. BRAVO!!!!! I laughed! I cried! I am so ECSTATIC!!!!!
The kit came with the anchors and the riollers for the bottom shelf. They clipped right on! Dishwasher cleans great now!
delivery of part was very quick, and my husband was able to remove the old part and install the new in about 10 minutes. No service call; no new rack; just a washer that is easy to use again.
Pulled off old rollers and snapped on new ones. Never easier!
No instructions. At first thought I needed instructions. A minute later I was attaching the new rollers. Simple and easy. Took less than 15 minutes. Would recommend these rollers.
The repair is just a couple of minutes job. All I had to do was to pop the wheel axle in the new wheels, remove the old wheels and put the new ones in. The wheel axles on the original one, were like clasps. All one needs to do is to pull the clasp to one side and slide the wheel out. The new one, just needs to be pushed in. In my case, I could have just swapped out the axles, but decided to change the whole set anyway.
Really all it took was removal of the old wheels which would not stay on anyway and the installation of the new ones. That required the axle and wheel being put together and the installing both of those on the lower rack. I was about to buy a new dishwasher when the salesmen told me about a product called Lemi Shine it saved my hundreds of dollars and the inside of my dishwasher looks brand new. With my new wheels I am good to go again.
Removed and replaced all rack wheels with new wheels and wheel axles. All I needed was new axles, as they are new and better, and solved the problem of the wheel falling off. G.E. should offer customers with this problem, new wheel axles at no charge, as they are very easy to exchange. The original axle was a bad design.
Simply pull out the old axle and snap in the new one. It is simple. Also the replacement axels were MUCH better quality than the originals. The bottom tray now slides in and out very easily. Note, if you have this problem, you do not need to replace the wheel, just the axle.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.