Ice Door Kit

PartSelect Number PS11723180

This kit includes the ice door, support, spring and delay. The heater ribbon is no longer attached - the heater is no longer needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker won’t dispense ice.
  • Door Sweating.
  • Leaking.
  • Door won’t open or close.
  • Ice maker not making ice.
  • Freezer section too warm.
  • Frost buildup.
  • Compare At

    $62.02
  • You Save

    $10.34
  • Your Price

    $51.68
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 26 reviews What's this?
 

14 of 19 people found this instruction helpful

Parts Used

  • Ice Door Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerJoseph S from Las Vegas, NV

Ice door holder arm broken

The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 17 people found this instruction helpful

Parts Used

  • Ice Door Kit

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerDavid from Winston-Salem, NC

Ice distribution door broke

At their site was ordering each piece by # and cost and it was adding up to be costly. Went to partselect and was doing the same and up pops the ice door kit. Was a little wary because my original had a heater tape to it. Got the kit and installed not a problem at all. 100% satisfied would recommend to anyone.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 15 people found this instruction helpful

Parts Used

  • Ice Door Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerRobert from Valencia, CA

Ice dispenser freezing up, dispenser door not closing completely.

First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainless panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 23 people found this instruction helpful

Parts Used

  • Ice Door Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJohn from Willington, DE

Broker door on ice shute

hardest part was getting up the nerve to pull front cover because it is plastic afraid i would brake it pull from bottom and lift up one screw holds old door inplace uplug electric new door doesn't have electric that it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used

  • Ice Door Kit

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerCarl from Mt Juliet, TN

Plastic door bracket for icemaker chute broken

Googled with question about how to get to the repair as there were no screws on the faceplate. Found I had to lift the faceplate at the bottom and pry out. Was kind of hard to get the long spindle back through the ears of the bracket holder along with getting the spring of the door lined up for the spindle to pass through to the other side. Finally got it right and then just put it all back together. Frustrating at first but I had to get it done as my wife was tired of having to take large clumps of ice out of the ice tray..three years wait for the repair. That door being open let warm air in and let the ice melt just enough to stick together in a clump. All is well now. Longer you wait the more appreciative she is however. ha

Help other customers find the most helpful instructions.

Were these instructions helpful?