Ice Door Kit

PartSelect Number PS11723180

This kit includes the ice door, support, spring and delay. The heater ribbon is no longer attached - the heater is no longer needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker won’t dispense ice.
  • Door Sweating.
  • Leaking.
  • Door won’t open or close.
  • Ice maker not making ice.
  • Freezer section too warm.
  • Frost buildup.
  • Compare At

    $62.02
  • You Save

    $10.34
  • Your Price

    $51.68
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 26 reviews What's this?
1-5 of 26
 

338 of 397 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerBILL from BATESVILLE, MS

Front door ice wouldn't work and air going into freezer

Thanks to the pictorial diagram, I was able to order correct parts. It was just a matter of removal of broken parts and replacing them. Ice maker now working and air is no longer getting into freezer which was freezing up ice maker. Thanks for timely delivery, now I am able to use ice dispenser, which I haven't used for long time. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

92 of 107 people found this instruction helpful

Parts Used

  • Ice Door Kit

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

Customerhelen j from murrells inlet, SC

Where ic e dispencer spring is held to door broke at mold

after ordering ice dispencer repair kit, and removing the outer parts found out that the problem was the ice dispencer door shell . this part is no longer available.It seems to me that if whirlpool wants to have return customers they have to stand behind the product. Well I made a L bracket and drilled a hole to to recieve the spring keeper and glued this to the housing and used a 3 1/12"finishing nail as the pin all works fine

Help other customers find the most helpful instructions.

Were these instructions helpful?

94 of 115 people found this instruction helpful

Parts Used

  • Ice Door Kit

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerDavid from Chesterfield, MO

Warm air getting into freezer

Patience is a virtue. The kit really works. 1st, lift the front plate of the ice dispencer by placing a flat head screw driver into the two slots at the bottom of the panel. When the panel is lifted up slightly at the bottom, push up on the panel to remove it. Careful not to break panel and the wires attached. Next, remove the wiring panel by removing the two screws on left and right sides. Then, unplug the old black ice cover from the wiring panel (this is the heating plug that you will nolonger need). Next, remove the parts and replace them with the parts in the kit, noting where each part comes from, etc. All parts in the kit are necessary and should be used. Some of the replacements need trial and error. Patience will be important. Also needed is a person that loves to solve problems, especially because the kit does not come with instructions. But the kit definitely works!

Help other customers find the most helpful instructions.

Were these instructions helpful?

36 of 43 people found this instruction helpful

Parts Used

  • Ice Door Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerRay from San Antonio, TX

Ice door was broken

1) At bottom of ice maker trim there are two small slots at right and left ; use screw driver to pry away from door; lift trim upward away from door 2)using 1/4" nutdriver remove screws from 4 corners, 3) remove 2 screws from control panel 4) disconnect all wires/cables and set exterior panel aside. 5) locate 2" pin that runs through door spring and use needle nose pliers to remove round clip on left end of pin don't lose this clip 6) while pushing ice maker lever (where you would push with your glass) use needle nose to pull the long pin out to the right 7) Remove all remaining parts by hand (i.e. the pin, the dash pot and white lever and the ice door) 8)slide new control lever into slots on exterior side of the new door 9) -tricky part- using needle nose, push pin back through the right hinge point, the new lever, the new door, the new spring and the left hinge point (note the new door has no electric wire connector) 10) using the needle nose, carefully replace the little round clip on the left end of the metal pin. 11) reconnect all the wires (don't worry about the wire that had been connected to the door wire, just fold it aside) 12) replace two screws screws in control panel and four screws at corners of exterior panel 13) snap outer trim panel back in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

27 of 37 people found this instruction helpful

Parts Used

  • Ice Door Kit

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerDwight from Marietta, OK

Door chute broken

First removed the outside cover plate which was some what scary not to break plastic cover. Had read about another discription of removal of cover to start from the bottom because the top is inserted in slots that would have broken if removed from the top. After cover plate removed it was simple to remove the broken parts and install the new parts. The most difficult part to put back in was the spring and rod had to be inserted the same time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 26