Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11722130
Sold individually. This part has been updated by the manufacturer. It may appear different but will still function the same.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.
Help other customers find the most helpful instructions.
Were these instructions helpful?
unplugged refrigerator and shut off water, removed one screw and loosened two more, after removing one side of the ice bucket rail, unplugged electrical from old ice maker. Then I removed the bail and out on new one, reinstalled ice maker in reverse order from taking it out.
By sliding the drawer out and lifting it up at the end, the drawer will come right out. By installing the new drawer in the same sequence, the job is completed. As for the filter, it is located inside the refrigerator compartment on the upper right side.Simply remove any items from the top shelf that may be in the way, and then push in on the tab that extends out from the filter housing. The filter and connector will swivel down at that point,simply hold the connector in one hand to stablize and with the other hand, twist the filter counter-clockwise to remove the filter. To reinstall the new filter, remove all protective covering from filter. Plase filter against filter connector and turn until tight (1/4-1/2 turn).Raise complete assemble upwads until tab snaps back into place. Installation is now complete, next purge the air out from water supply by placing a pitcher or other large container under the dispenser and activate.Run water for a minute or so until all air is removed.
I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady thought process on the problem helped disengage the darned old filter!
The switch-out of the water filter was simple with good instructions on the box.The part was delivered very, very quickly!
I unscrewed the old one and replaced it with the new one. The real benefit was I got the exact part I needed w/o a 30 minute drive and sales people that ignored me. I had gone to the local store the day before and come home with the wrong part because i could not get assistance and the part # I had did not match what was labled on the package. I used the same part # on the website and got exactly what was needed, less that 48 hrs after I ordered it. thanks for the prompt service. we will be a repeat customer
Crisper drawers:1. Removed crisper drawers from refrigerator.2. Removed drawer front decoration panels.3. Unpacked, inspected and rinsed out new drawers.4. Attached drawer front decoration panels.5. Transfered vegetables and fruit from old drawers to new drawers.6. Installed new drawers in refrigerator.7. Closed refrigerator door.8. Total time about 15 minutes, no tools required.Ice & Water filter1. Opened filter compartment cover2. Removed old filter, drained into sink and placed in the trash.3. Installed new filter4. Bled the water line with ice water tap button (be aware when the air in the line exits the spigot, it create a lot of spray and you may need to cleanup the water that splash out of the bottom of the container used to capture the water during the bleeding process.)5. Close the filter cover and refrigerator door.6. Total time about 10 minutes and no tools required.
unscrewed to removed old and screwed in new
First I removed the drawers above the pantry drawer. Then I took out the pantry drawer. I unsrewed 3 screws that attached the part to the refreg. I then removed the rails that were attached to the part I was repalcing and put them on the new part. I then install the new part. Put the firg back together. It was extremely easy and took about 5 minutes to do.
I firts pulled the refrigerator away from the wall. Un plugged it and removed a metal cover off of the back of the fridge. A clear plastic container was behind the metal pael. Removed the connectors and snapped the pld board out, Put in the new one and reinstalled the cover. Had to get the code number from theinside of the frifge and entered it into the front key pad. This step took a bit of figuring to advance the numbers using the key pad but with some trial and error...Repair done.
Turned old one until it snapped out. Replaced it with a turn.
This is the 2nd time I had have had to replace the center rail in 2 years....
Remove (3) screws; Removed existing bracket and installed new bracket. Great Service from PartSelect
Turned the old one to unseat and replaced with a new one in the reverse order.
First I removed the outer shell part then removed the 4 screws holding the ice bin together.After taking the parts out of the old ice bin it was easy to put all the new parts together except the new helix end cap which was a bit tricky to put it in place.It wasn't difficult to reassemble but I would stongly suggest taking notice how everything fits together before taking it apart.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.