Quick Question!

Have you ever purchased from PartSelect.com before?

11722130-1-S-Whirlpool-EDR4RXD1-Water Filter
11722130-1-S-Whirlpool-EDR4RXD1-Water Filter http://www.partselect.com/Schematics/Maytag/4MBJPGQH.gif

Water Filter

PartSelect Number PS11722130

Manufacturer Part Number EDR4RXD1
Manufactured by Whirlpool

Sold individually. This part has been updated by the manufacturer. It may appear different but will still function the same.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not dispensing water.
  • Ice maker not making ice.
  • Leaking.
  • Noisy.
  • Ice maker dispenses too little ice.
  • Fridge too cold.
  • Touchpad does not respond.
  • Ice maker won’t dispense ice.
  • Compare At

    $86.80
  • You Save

    $14.47
  • Your Price

    $72.33
In Stock
Order within the next 6 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 38 reviews What's this?
31-38 of 38
 

0 of 2 people found this instruction helpful

Parts Used:
  • Water Filter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Eric from Noank, CT

Replacing filter

Really easy, simple instructions, and it was on my doorstep 3 days after I ordered. Much simpler than dealing with the appliance store, where I'd have to drive to the store, order the filter, wait 7-10 days, and return to pick it up. Ughh! Internet is the way to go!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Rafe from Tuscola, TX

Ice maker stopped making ice.

I turned off the water supply to the refrigerator, and I removed all the food, baskets, and shelving from the freezer unit. I removed three screws holding the ice maker, lowered it, and unplugged the wiring harness. The clip holding the wiring harness in the ice maker was not real obvious, but I found it okay. I took the bail and the front cover from the old ice maker and placed them on the new ice maker. Two of the screw holes for the new ice maker were slotted allowing me to start the screws in the side of the freezer prior to installing the new ice maker, and the third screw was no trouble to start. I really did not need the instructions I ordered, but I am cautious toward having everything I need in case something does not go as planned. This was a very easy repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used:
  • Water Filter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Elizabeth from Greencastle, IN

It was time to change the filter for the first time

Opened up the door that covered the filter, unscrewed it and put the new one in and closed the door back up.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used:
  • Water Filter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Marlene from Baltimore, MD

Indicator light showed water filter needed to be replace

Dropped down the housing for the water filter, twisted, removed item and slotted in the new filter. Easy as pie.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: michael from boca raton, FL

Entire freezer compartment was cascaded in ice and icemaker had been noisy

Turn off power first or unplug. Get a light so you can see. Read these directions through one time to reduce the learning curve. Remove ice cube bin. 1/4" nut-driver will do most of the work. Remove flexible water fill tube from back of ice cube maker, move to the side, out of the way. Remove screw from "L" shaped bracket from the bottom of maker, close to the front. Two more 1/4" screws to go. There are (2) screws on the top left that hold the maker to wall. Loosen the front screw, but do not totally remove, unit will lift off of front screw. The back screw had to be completely removed because of a clip that holds the wiring on the back of the maker. The wiring is attached to the back wall in the form of what is called a Molex connector, a white plastic connector. This is probably the hardest part of the job, wiring access. The air deflector blocks any free access, so you have to just grab and depress the prongs to release the Molex from the wall. With wiring disconnected, remove entire assembly. Use a flat-tip screwdriver to pop the white cover off of the front of the maker to use on the new one. Same goes for the wire cube arm that sets out over the ice cube bin, taking the front out first (pulling straightout) then pivot arm 180 degrees and remove from back. Remove wiring harness from front of maker. Re-install on maker, it goes in one direction only, look at the configuration before you pull it out, and put in the same way. Make absolutely sure you re-install it so it clicks in all the way. If not, it won't work. I had to remove the ice maker again because I did not make this connection properly the first time. So I did the whole job twice. You have to put the job back in reverse of the way you took it out. The new one works great. I should have done this about a year ago. The old one had been making a noise and I ignored it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Socket set
Customer: Susan from NORTH HOLLYWOOD, CA

Cover to pullout drawer hinge broken

Required removal of the entire endcap piece. A total of 5 screws. Hardest part was realizing i didn't have the right size socket wrench to start. Got that and replaced all 5 screws in under 5 minutes. $18 for part, $10 for tool.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 6 people found this instruction helpful

Parts Used:
  • Water Filter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: James from Tampa, FL

Ice maker would not produce ice, filter replace indicator illuminated

Only second replacement of water filter required. Readily identified, procured and replaced water filter. Filter replace indicator deiluminated. However, ice maker still is not producing ice following replacement. Any suggested corrective actions would be greatly appreciated as I have lived w/o ice for two weeks now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 46 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools:
Customer: Holly from Lowell, IN

Handle on the french door (3rd door) freezer broke

I had to get on-line to find how to do it. It originally seemed easy enough, but it was not as easy as it looked. I sliced my finger trying to get the brackets into the butterfly clip, but after about 30 minutes of dogged-determination, I was successful...

The water filter replacement was easy, once I broke the tighter than all get out old filter.

Sure did save me a lot of money doing it myself.

Help other customers find the most helpful instructions.

Were these instructions helpful?

31-38 of 38