Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11722128
The single water filter is a part for your refrigerator. This filter has been updated by the manufacturer and although it may appear different, it will still function the same. The most common reason for needing to replace this filter is if your refrigerator is not dispensing water or ice, and you find that there is a leak. It is recommended that the water filter be replaced every six months to ensure proper removal of impurities and to ensure flow rates. The function of this part is to reduce contaminants in your water supply for a certain period of time. You will not need any tools to complete this installation.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
We didn't know where the product went and it was very difficult to install.
Help other customers find the most helpful instructions.
Were these instructions helpful?
First I shut the water off to the refrigerator.then i pushed the big button in the middle of the grille below the refrigerator door. pulled out the old filter, took the front cap off the old filter put it on the new filter. took the two red caps off the new filter. pushed the filter in till it locked in place. all done! Turned the back on.
It's simple enough in theory: read the side of the box and follow the instructions. BUT you need to really push the knob in pretty hard (I am a girl, and my hand strength isn't that good). If you don't, when you turn the knob, the filter won't come out, then it's tougher. So: make sure the knob pops before you turn!
It was ridiculously easy. Push the button on the filter canister holder at the base of the refrigerator and the spring-loaded mechanism came out smoothly. I unplugged the old filter, took the cap off the new on and plugged it in. After reinserting the filter canister holder and locking it in place, I heard the whoosh of water once again moving through the filter. Very satisfying and very easy to do.
It turn one turn on the filter holder, pull out and put new filter in done
The lower spray arm unscrews. From inside the dishwahser, put a screwdriver through the tab slots and unscrew the tower from the floor. It's pretty tight for plastic.The upper spray arm has screws on the top of the dishwasher. You must slide the dishwasher out from underneath the countertop to get to the screws. Normally that's just the two screws above the door that screw into the countertop. Pull the insulation back and unscrew the arm from the top of the dishwasher. Reverse to reinstall.Piston and nut assembly for check valve: Inside the dishwasher at the back there are 2 screws that hold a screen down. Remove the screen. Take out the check valve and replace it. It was still functional in mine, it looked like food gunk had built up on it and impeded the check valve action.The flapper chec is a rubber flap in the drain tube that connects to your sink drain. You have to pull the dishwasher out from under the sink to get to the end of the drain tube that connects to the dishwasher. Take the hose clamp loose and remove the drain tube from the dishwasher. Then unscrew the plastic fitting that you just took the drain tube off of. The flapper chec is there. It had turned brittle and didn't flap anymore. It is a similar setup to the rubber seal at the end of your garden hose.
It was SOOO easy, I turned and popped out the old filter and turned and snapped in the new one....I don't even think it took a whole minute to replace!!
Removed the icemaker to see if I could determine problem; motor was seized; got part numbers and ordered from you; parts arrived next day (even though overnight delivery wasnt' requested - so THANK YOU!); compared new parts to original to be sure of fit; reassembled unit; reinstalled in freezer, and waited for the sound of water filling the tray. Producing like brand new again! Cancelled the service call w/ Sears for the following week (when it was convenient for them) Loved your service!
It took less than 5 minutes to remove the old filter and install the new one. Push a button and the old one pops out, stick in the new one, and you're done.
followed the instructions on the box
We took out the old filter and put in the new one. Ran out a few gallons of water then it was ready to use.
Easy as pie, I followed the directions on the box that the replacement filter came in, and installed it and the cap simply and easily.
I removed the cap from the filter pushed a lever and removed fliter. I replaced the old filter, removed the caps on the new one and slid it into channel after replacing the outer cap. I removed water from the spigot for 4 mins. and it was ready to go. I pushed the reset button to get the green light to come on.
Just put the new one in.
Built-in filter was corroded due to age. New filter corrected problem.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.