Quick Question!

Have you ever purchased from PartSelect.com before?

11722115-1-S-Whirlpool-661570V-Drive Belt
11722115-1-S-Whirlpool-661570V-Drive Belt 11722115-2-S-Whirlpool-661570V-Drive Belt 11722115-3-S-Whirlpool-661570V-Drive Belt http://www.partselect.com/Schematics/Maytag/JO3DJX3W.gif

Drive Belt

Compare At

$15.71

You Save

$2.62

Your Price

$13.09
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11722115
Manufacturer Part Number 661570V
Manufactured by Whirlpool

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide.

This part works with the following brands: Kenmore, Whirlpool, Maytag, KitchenAid, Crosley, Inglis, Admiral, Amana.

This part works with the following products: Dryer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Noisy.
  • Will not tumble.
  • Will Not Start.
  • No heat or not enough heat.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 9 reviews What's this?
1-9 of 9
 

100 of 140 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: Lucas from Nuevo, CA

Need it a new pulley and belt

I did the repair all by my self and just payed for the parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

44 of 52 people found this instruction helpful

Parts Used:
  • Drive Belt
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Larry from exeter, RI

Broken belt

First I removed back and top of dryer, then the support braces holding the drum, after that I took the drum out and the blower covers and cleaned the whole dryer of lint and other debris. Installed the new belt and then reassembled the dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

27 of 42 people found this instruction helpful

Parts Used:
  • Drive Belt
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: john from goldsboro, NC

Dryer not spinning

I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Dennis from AUSTIN, TX

Dryer drum was not turning when started.

I moved the dryer to a location where I could get to both the front and back sides. I opened the back by first removing the top cover and then the back. It requires either a Phillips head screwdriver or a quarter inch socket. In addition, it requires removing the four power wires which connect to the computer. If you are unfamiliar with the wiring layout, take a photo with your cell phone which you can then refer to when re-assembling. Once the back was removed, I saw that the belt was still intact, but the pulley which provides tension to the belt was frozen. Take a photo of the belt route between the motor and the pulley. Try to get the spring position in the photo. Remove the belt from the pulley by reducing the tension and then sliding the belt out (this assumes the belt is not broken). The pulley arm is held in place by a single bolt which can be removed by a socket set. Remove the arm with the pulley attached. Examine the pulley to figure out why it is frozen. In my case, the pulley had been frozen for some time and the belt had actually chewed through the pulley and was sliding (polishing) on the pulley axle? I used a pair of pliers to loosen the destroyed pulley by rotating it back and forth over the axle while gripping the arm the axle is attached to. As it loosened up I worked it off the axle. I used a cloth to clean the axle of grime from the belt, pulley, and dryer lint. The new pulley comes with a washer and triangular plastic "fastener". First you put on the washer, then the pulley and then you secure it on the axle by sliding the triangular fastener over the axle so it sits in a small grove near the end of the axle. Then put the pulley arm back by replacing the bolt. Make sure you do not overtighten the arm since it is intended to rotate about the bolt. If the dryer belt breaks, the spring will pull the arm down and throw a cutoff switch. Its operation should be obvious. Once the arm is back in place, refer to your photo and replace the spring (this can be tricky and frustrating, particularly if you don't use something like needle nose pliers). Once the spring is in place, depress it and re-install the dryer belt. Refer to the photo you took earlier if you've forgotten how the belt was routed. Then re-install the dryer's back panel, re-attach the electric wires (again refer to the photo you took earlier), and re-attach the top cover. You might want to test your handiwork at this point before you reconnect the dryer vent

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: John from HATFIELD, PA

Dryer would not start.

With the help of YouTube, I was able to watch videos of how to disassemble and reassemble the dryer. I watched a video showing where the Thermal fuse and Thermostat was located as well as how to test them with a meter. I watched another video showing how to replace the drum belt, showing step by step instructions. Without YouTube it would have been a whole different story!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Drive Belt
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Ken from LOMBARD, IL

Broken belt

Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Very Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: angelo from NATIONAL CITY, CA

No issue at all!

even though my appliance is a little different from video i still was able to repair my appliances based on the video. definitley cheaper than buying a new one!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Socket set
Customer: Mark from Sheffield, PA

Drive pulley broke. Looked like clip holding it on broke and pulley was running crooked.Belt was squealing some a couple of weeks before it broke.

Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Drive Belt
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Enrique from SAN DIEGO, CA

Noisy dryer and taking long to dry clothes

I removed the top first followed along with removing the side bracket that holds the circuit board. I then proceeded with removing the bottom cover and front panel. I disconnected the front panel from the control board and was able to slide the front panel upward. The door and blower housing was a bit tricky to pull out without thinking I was damaging something. I then replaced all the seals and cleaned the dryer after removing the drum and belt. I also replaced the drum support rollers. Afterwards I put everything back together and had an "E1" error and I pulled the thermostat out and wiped it down from all the lint and dryer worked perfect after that. Dryer takes the right amount of time to day clothes and no more rumbling noise. The instructions videos were VERY helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-9 of 9

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11722115
Manufacturer Part Number: 661570V
Brand Model Number Description
Kenmore10687884100Dryer
Kenmore10687884300Dryer
Kenmore10687884600Dryer
Kenmore11060052990Dryer
Kenmore11060052991Dryer
Kenmore11060056990Dryer
Kenmore11060056991Dryer
Kenmore11060072990Dryer
Kenmore11060072991Dryer
Kenmore11060092990Dryer
Kenmore11060092991Dryer
Kenmore11060094990Dryer
Kenmore11060094991Dryer
Kenmore11060096990Dryer
Kenmore11060096991Dryer
Kenmore11060097990Dryer
Kenmore11060182000Dryer
Kenmore11060901990Dryer
Kenmore11060902990Dryer
Kenmore11060904990Dryer
Kenmore11060907990Dryer
Kenmore11060912990Dryer
Kenmore11060922990Dryer
Kenmore11060924990Dryer
Kenmore11060927990Dryer
Kenmore11060932990Dryer
Kenmore11060936990Dryer
Kenmore11060942990Dryer - Kenmore Dryer
Kenmore11060952990Dryer - Dryer
Kenmore11060954990Dryer