BBB A-Plus
http://www.partselect.com/Schematics/GE/GE_Thumb/00120714i01.gif
See part 56 in the diagram

LIGHT DISPENSER

PartSelect Number PS1155189

This is also known as a light bulb.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Lights will not turn on
In Stock

  • Compare At

    $2.51

  • You Save

    $.42

  • Your Price

    $2.09
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos

For installing this part.

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 NEXT > 1-12 of 12

 

9 of 11 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerWilliam M from Ft Myers FL

Solenoid had become rusted/crank door wouldn't close

First, had to use punch tool to pop out electronic face panel. Face unit still connnect via wires. Use painters tape to hold against refrig. Next, Remove ice/water dispenser and also tape to door. This will give you access to solenoid. Remove the 3 screws holding it in place and unplug fsolenoid from Face Panel. Screw new solenoid and place and connnect to Panel. Goood idea is to unplug regrig. while doing this and put a little WD-30 on shaft of solenoid. May want to order new screws, could be rusty, that hold solenoid in place. Sounds a bit complicated but not that bad a job. You'll save over$100 over GE's service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerAnthony from Miramar Beach FL

Frost in frezer compartment where chute meets ice cube maker

REMOVED FRONT PANEL (using small screw driver) BY POPPING IT OUT, disconnected wire from solenoid, REMOVED SOLENOID WHICH WAS RUSTED, 3 SMALL PHILIP HEAD SCREWS HELD IT IN PLACE INSERETED NEW SOLENOID,connected wire snapped front panel back in. CLAPPER VALVE CLOSES TIGHTLY and no frost in frezzer, SAVED MY SELF A BUNCH OF MONEY.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerStella from Puyallup WA

Drive cup broke, light went out

Just had to pull ice maker drawer out and replace the drive cup which was very simple. Light bulb on door dispenser was kind of hard to get back in cause it is such a small space to screw the bulb in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

    • LIGHT DISPENSER

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerAustin from New Portland ME

Ice door light bulbs burned out

found the correct bulbs, the hardest part.
un screwed old bulb.
Screwed in new bulb.
Waa La,
There was light.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerDennis from Frenchburg KY

Light replacement in dispenser

kick plate replacement at the base of refrigerator. Very easy to replace. No rocket science needed :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

Customernoah l. from crestview FL

Plastic from auger [front] had broken

removed the depenser or ice collecter disassyble,replace the new auger and install the collecter tray in freezer.the bulbs i got was for use as i needed,at a later date i have not been able to fine the ice and water depenser bulbs on the open market.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 15 people found this instruction helpful

Parts Used

    • LIGHT DISPENSER

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerGerald from Lincoln CA

Light burned out

unscrewed lamp and replaced it with new one!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

Customerdan from columbus OH

Water filter and light dispenser replacement

My water filter was a breeze to install. Just push up and to the right and it locks right in.

As for the Water Dispenser light. Just screw it in!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerjoseph from HAMPTON VA

Broken dispenser engager

Pretty easy to repair. Only took a few minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Socket set, Wrench(Adjustable)

CustomerBruce from Margate FL

Water dispenser not working

Simple straight forward process. Remove the refrigerator back cover, unhook the inlet water lines and replace water valve.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerJOSEPH from FORT MYERS FL

Ice shute flapper did not shut

Used awl inserted into 3 holes at bottom of dispenser toutch pad #93 to release it from mount. Disconnected wire to solenoid & rested panel in door opening. Removed 4 screws holding dispensor housing shield #69. Removed 3 screws holding solenoid & connecting arm #36. Solenoid very rusted. Cleaned inside of ice dispensor with bleach to remove crud & mold. Installed solenoid & reassembled shield & touch pad. Replaced light bulb in dispenser. Flapper now closes tight, problem solved.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 8 people found this instruction helpful

Parts Used

    • LIGHT DISPENSER

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerPaul from Damascus VA

Ice dispenser light wouldn't light

remove old bulb by screwing it out/install new bulb by screwing it in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 NEXT > 1-12 of 12