1146950-1-S-Frigidaire-134511600         -Drive V-Belt
1146950-1-S-Frigidaire-134511600         -Drive V-Belt 1146950-2-S-Frigidaire-134511600         -Drive V-Belt

Drive V-Belt

PartSelect Number PS1146950

This belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Burning smell.
  • Pumps but will not spin.
  • Unusual Noise.
  • Will not agitate.
  • Shakes and moves.
  • Spins slowly.
  • Will not drain.
  • Compare At

    $13.69
  • You Save

    $2.28
  • Your Price

    $11.41
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 24 reviews What's this?
16-24 of 24
 

3 of 5 people found this instruction helpful

Parts Used

  • Drive V-Belt

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerPeter from Lynnwood WA

Noisy operation - "chugged" during operation.

With prep work mentioned below and a good flashlight it takes about 15 to 30 minutes if you're a good handy-man. If you're not, get a neighbor or friend who is. This repair isn't rocket science, but does take a some mechanical aptitude. This unit is a washer/dryer combo unit. Unplug power cord and remove water supply hoses, the drain hose and dryer vent if required to obtain easy access to front panel. There is water in all the lines, so have some towels and a small gallon bucket to help drain the lines if disconnected. Remove two screws on bottom of front panel. Be sure there is about 2 inches from washer/dryer to floor in front to allow front panel to drop directly down, then pull panel out lightly. Wood spacers or similar are recommended under front feet to prop-up front of washer. (There are two tabs on each side of the front panel. The panel must be pulled straight down to clear tabs). Another option is tilt back the washer/dryer about 60 to 75 degrees unit to make the front panel more accessible if all is disconnected in back and you have the room to do so. Once the front panel srews are removed, you may have to place an object (thin pry bar or screw driver) between the top of the washer unit and the front panel for release (be careful not to dent or scratch the top metal or front panel. Remove front panel and set aside. Locate belt near bottom and tensioner pulley (it moves back and forth laterally), push in tensioner pulley to relieve pressure on belt and remove belt from small pully wheel at motor, then the large drum pulley wheel. Place new belt on large pulley first, then small pulley. Push in tensioner pulley and move middle of belt to the inside of the tension pulley to take up the slack. This process is somewhat hard. It takes good hand strength. Be sure the belt is aligned in pulley grooves. Place washer/dryer back in level position, re-attach water supply hoses, drain hose, dryer vent line and power cord, if removed for repair. Check for leaks in water supply lines and be certain the drain hose is well attached to the drain pipe. (This is a good time to clean or replace the dryer vent line to prevent possible lint fires.) Plug in washer/dryer unit and test as if washing a small load. Re-install front panel after successful test in run operation. The part came quickly and fit perfectly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Drive V-Belt

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerLewis from Thornton CO

Burning rubber smell

Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Drive V-Belt

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerGeorge from Sault Ste. Marie MI

Drive belt old and stretched

unplugged machine. pried up with large regular screwdiver on top washer lid. removed two phillips screws bottom of front panel, had to use rubber mallet to drive front panel down to remove as was rusty and old. removed old belt using screwdriver. put new belt under tub pulley and put belt on small pulleys. kept moving tub and springs by pushing on tub. Took several tries to get new belt to go on the large tub pulley but finally did it. I used the instructions you gave for replacing broken drive belt and it worked. replaced front panel and two phillips screws, put top back on and away it went.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 6 people found this instruction helpful

Parts Used

  • Drive V-Belt

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsWrench set

CustomerANNA from STATEN ISLAND NY

Motor burnt out

my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 15 people found this instruction helpful

Parts Used

  • Drive V-Belt

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDave from Murrieta CA

Belt broke

Removed old belt. Installed new belt.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drive V-Belt

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerSteve from Carrollton TX

Drive belt was noisy-slipping

I just popped up the top front using a large straight (slotted) screw driver, then removed the 2 screws at the bottom front, then the whole front panel popped down about a half inch to be lifted out of the way. I found the old drive belt way down under the motor (still attached as normal), very near the floor and removed the worn out belt by hand, and replaced it with the new belt by hand also. The spring loaded belt tightener- idler wheel makes this a very simple process to accomplish. Then, I replaced the front panel-- all done. Works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drive V-Belt

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerodell from Elizabethtown KY

Broken belt

I took off the front panel of the washer and placed the belt on the large tub wheel and then the smaller wheel. I placed the belt over the adjustable third wheel and turned the tub in order to get the belt all the way in the grooves. Thirty minutes max to replace. Thanks, my order was 100% satisfactory

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Drive V-Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMohamad from Chicago IL

Washer was not spinning

We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.

I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerKaren from ft Lauderdale FL

Maintenance repairs

after 6 years of use, these parts needed to be replaced. I was reffered to ur website by a friend, and I am glad I purchase the parts @ the right place. Helpfull and fast responses.

Thank you!

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-24 of 24