Quick Question!

Have you ever purchased from PartSelect.com before?

1145747-1-S-Frigidaire-134371210         -Short-Tubed Water Inlet and Dispenser Valve without Sensor
1145747-1-S-Frigidaire-134371210         -Short-Tubed Water Inlet and Dispenser Valve without Sensor 1145747-2-S-Frigidaire-134371210         -Short-Tubed Water Inlet and Dispenser Valve without Sensor 1145747-3-S-Frigidaire-134371210         -Short-Tubed Water Inlet and Dispenser Valve without Sensor http://www.partselect.com/Schematics/Frigidaire/4EQUPUSW.gif

Short-Tubed Water Inlet and Dispenser Valve without Sensor

PartSelect Number PS1145747

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Leaking.

Compare At

$109.06

You Save

$18.18

Your Price

$90.88
Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Water Inlet and Dispenser Valve

Part Number 1145692

This part comes with the sensor/thermistor.

$56.42
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 6 reviews What's this?
1-6 of 6
 

6 of 9 people found this instruction helpful

Parts Used:
  • Short-Tubed Water Inlet and Dispenser Valve without Sensor
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Tracy from Brazil, IN

Wet clothes after spin cycle on front loader

Found that the fill valve was leaking and clothes would be wet if not removed right away.
Removed 2 screws from back of top panel and removed panel.
Disconneced water lines and two screws held valve assembley to detergent dispenser and unplug wires from the 3 solenoids

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
  • Short-Tubed Water Inlet and Dispenser Valve without Sensor
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: Andrew from Mastic Beach, NY

Water leaking from inlet hose area.

Close examination revealed cracked plastic inlet area. I removed top of machine any carefully was able to loosen an pull damaged (froze over the winter) part back to remove. Attachment screws difficult to access, had to use magnetic screwdriver attachment during reassembly. Always iffy when working with plastic parts.
Part arrived 2 days later, took about 40 minutes to install.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Short-Tubed Water Inlet and Dispenser Valve without Sensor
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Jim from Tucson, AZ

Crack in plastic housing

first removed top of machine. removed 3 valve core wires set. Then removed left top screw on valve. Then removed vent tube to get to lower right screw. disconnected hose connect rack so valve housing could be removed & new installed. Rapped insulation around valve & installed. Put everything back together in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Short-Tubed Water Inlet and Dispenser Valve without Sensor
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Alan from Eugene, OR

Washer was in the garage, and we had a hard freeze. Water in the valve froze, breaking the valve.

Took the top off the washer, removed the valve, installed the new one, back in buisness. It was so easy to order the part, and have the repair done in no time.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Short-Tubed Water Inlet and Dispenser Valve without Sensor
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Kathy L from Twin Lake, MI

The part cracked from water freezing

First I removed the two screws that hold the part in place. I then pulled the part out about 3 inches and disconnected the three wires from the part and put the new one in

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Short-Tubed Water Inlet and Dispenser Valve without Sensor
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Wrench (Adjustable)
Customer: Jennifer from Middleboro, MA

The valve had cracked so water was leaking out from the cracked area.

After getting a quote for $140 for a repair, I decided to try ordering online and hope for the best. I am delighted to say it was incredibly easy! All I had to do was remove the broken valve by unscrewing the water hoses with a wrench and remove two screws that held the valve on with a screw driver. Next, I popped in the new piece, replaced the screws with the screwdriver and attached the hoses, then tightened them with the wrench. Very easy! 10 minutes total.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-6 of 6