http://www.partselect.com/Schematics/Frigidaire/Frigidaire_Thumb/9OOZSWQ0.gif
See part 54A in the diagram
http://www.partselect.com/Schematics/Frigidaire/Frigidaire_Thumb/9OOZSWQ0.gif

Infinite Burner Switch - 8" - 240V

PartSelect Number PS1145040

This switch controls the stove top 8" surface burner.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Element will not heat.
  • Will Not Start.
  • Compare At

    $25.69
  • You Save

    $4.28
  • Your Price

    $21.41
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Infinite Burner Switch - Small Element - 240V

Part Number 1145039

This switch controls the stove top surface burner.

$25.18
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 16 reviews What's this?
 

8 of 14 people found this instruction helpful

Parts Used

  • Infinite Burner Switch - 8" - 240V

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerRobert from Andrews, SC

Switch had a diffirent lug configuration

made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Infinite Burner Switch - 8" - 240V

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerJerrold from San Marcos, TX

Switch not always turn off

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Infinite Burner Switch - 8" - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerArmando G from Alice, TX

Electric burner switch shorted out.

First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerJames from Caldwell, ID

The indicator light for burners broke and shorted agaist the back panel on range

This caused the burner switch cotacts to arc burning out the switches. It took 30 or 43 minutes to replace the switches and put the range back together. The bake element took 10 min. ti replace. Grandma has her range back and I am a happy grandpa!! Thanks for the help and we saved over $170.00 for the repairs. Jim Johnson

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

  • Infinite Burner Switch - 8" - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerKevin from Nashville, TN

Large burner would turn on high and not cycle off

TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range back in place. DONE

Help other customers find the most helpful instructions.

Were these instructions helpful?