Filter Gasket Assembly

Found a forum on the internet that said the Air Check Valve located under the screen on the bottom of the back wall inside the wash compartment may be the culprit. Took it out by using nut driver to remove screen, and twisting the part out. The seal was deteriorated. Repleacing the part was simply the opposite, and very easy.

I also replaced the screen on the floor of the wash compartment because the rubber was deteriorating there too. Here I had to remove the spray arm by carefully prying the locking tabs outwards and lifting the entire spray assembly upwards. Then, then plastic covers need to be unscrewed and removed. The new part had the plastic cage molded into it. So I discarded the old plastic cage. There are a couple of retaining clips that are a little tricky to get off the plastic posts. But, they can be removed by prying a standard screw driver underneath and working them off the post. Do not break the plastic post, and save the retaining rings. The new part does not come with any screws or retainers, so you will need to re-use them. Simply, place the new screen in position, slide on the retaining clips, and screw down the cage. The spray assembly is just slid back onto the shaft and snaps into place. A lot of writing, but was rather simple to do. 15-20 minutes.

Disconnect the dishwasher power supply and water connector.Then disconnect the drain hose.Take off the hose from the pump and on the plastic valve is the black valve flapper.Mine was swollen twice the size of the new one.Replace with the new one.You have to pull the dishwasher out and turn it over to do this.
The check valve was totally worn out.You must turn the dishwasher back to it's in use position and open up the door.Inside the lower rear wall is a plastic cover with 4 screws remove these and the cover.Then unscrew the piston and nut assembly and remove the check valve.Simply replace with the new parts and reinstall the cover.
I replaced the gasket before I reinstalled the check valve even though it looked ok.To do this you need to turn the dishwasher over again and remove the 4 screws dolding the resevoir the check vave is in.Replace the old gasket with the new one and reinstall the new gasket.Do this after removing the old check valve and before intalling the new one.
On the bottom inside the dishwasher I noticed the large white gasket on the floor was falling apart so I replaced that also.I'm glad I did because below this assembly there is a reusable plastic filter that was totally plugged that I cleaned and reinstalled before relacing the filter gasket assembly.To do this you must remove the plastic water jet.With a screw driver there are 2 plastic tabs that must be carefully pulled out so you can pull out the water jet.Remove the 2 screws and plastic cover on top off the gasket assembly.Retain the 2 screws but you will not need the cover it is part of the new gasket assembly.There are two clips you need to carefully pry off.Then lift out the old gasket assembly and replace with the new one.Reinstall the 2 screws that held the old cover before and If reinstall the old clips if not damaged.You can purchase new ones but usually not needed.Then gently snap the water jet in place.
Put the dishwasher back under the counter and reconnect the power,water line and drain hose.

FILTER GASKET ASM:

1. Manually unscrewed the lower dishwasher sprayer from the base of the dishwasher. (The filter gasket cannot come out with this in the way.)

2. Using a nut driver, unscrewed the old plastic filter cage in the rear.

3. Thanks to a tip from another user on this site, I carefully pried up the metal grommets on the two plastic studs in the front. I did this slowly with a flathead screwdriver, as I was worried about breaking the plastic. (Some plastic did whittle off of the studs from the sharpness of the grommets, but not so much that they were ruined.) Note, the studs look like something that can be replaced if you break them. They are not molded into the tub, as far as I can tell.

4. Removed the old (rotten looking gasket). Be careful! The edges around the filter drain are sharp. Used a turkey baster to suck out water from the filter area and wiped away mildew. The filter recess had broken glass in it and some other yucky stuff.

5. Easily reversed process with the new gasket. The new one has a lighter color and has the plastic, upside down basket thingy built-in. (No sharp edges). I pushed the metal grommets back onto the plastic studs, working them down as tightly as possible. They seem to be holding well.

Piston and Nut Assembly for Check Valve:

I wasn't sure I needed this, but ordered it anyway after seeing comments that the seal can corrode.
Mine looked ok, apart from food build-up, but I replaced it anyways.

1. Removed the screened housing that covers the length of the bottom-rear using nut driver.

2. Unscrewed the existing valve manually. It was easy to do. Cleaned area out as best as I could.

3. Reversed process with the new part.

Looked up Model number on site, checked "symptoms", and 64% of the time it was the Piston & Nut Assembly, which was correct. While I had it apart, I replaced Filter Gasket that was deteriorating, and lower spary arm that had a crack. Very easy fix.

Just lifted it up and removed it. However in the process the pins or whatever the tabs are called were broken ( they help turn the thing that rises up and spins around to the top of the dishwasher) so now I have had to buy one of those. My son did the repairs and now we have one of those items on order. Hopefully this will resolve my dishwasher problems. It is a simple problem if you patience. He builds pools & spas so he should have no problems but he tackled this after a long day in the rain so it was not the best time. I believe I could have done it without destroying another part!!!

followed the instructions on line . it was as easy as that

replced gasket and roller assembly after reading previous persons detailed description of installing new redesigned gasket. Thought wrong part had been sent until I read his description of problem and intallation of new gasket. rollers were easy to install.

seal worn out
removed palstic screen in back 4 screw
removed piston and nut assembly by unsrewing
reassemble